Panasonic KX-TGP500B04 User Manual (English)

Other manuals for Panasonic KX-TGP500B04

Administrator's Guide256 pages

Service Manual131 pages

Questions and Answers:

N
Nancy SaundersJul 30, 2025
Why can't I hear a dial tone on my Panasonic KX-TGP500B04 Cordless Telephone?
- A
  Anna McintoshJul 30, 2025
  If you cannot hear a dial tone on your Panasonic Cordless Telephone, there might be an issue with the network settings. Verify the VoIP status in the Web user interface to ensure each line is registered correctly. It's also advisable to reset all equipment, confirm the Ethernet cable is properly connected, and check the firewall and port forwarding settings on the router.
S
shannon55Aug 4, 2025
Why does my Panasonic Cordless Telephone handset not ring?
- K
  kleindanielAug 4, 2025
  If the handset of your Panasonic Cordless Telephone does not ring, first adjust the ringer volume. Also, check the VoIP status in the Web user interface and confirm that each line is registered properly. Make sure that [Do Not Disturb] is set to [Yes], [Unconditional (Enable Call Forward)] is set to [Yes], and [Block Anonymous Call] is set to [Yes]. Finally, verify that [Do Not Disturb], [Enable Call Forward], and [Block Anonymous Call] are not controlled by your phone system.
M
michael55Aug 8, 2025
Why does my Panasonic KX-TGP500B04 base unit not ring?
- D
  Dylan YoungAug 9, 2025
  If the base unit (KX-TGP550 only) of your Panasonic Cordless Telephone does not ring, first adjust the ringer volume. Also, check the VoIP status in the Web user interface and confirm that each line is registered properly. Make sure that [Do Not Disturb] is set to [Yes], [Unconditional (Enable Call Forward)] is set to [Yes], and [Block Anonymous Call] is set to [Yes]. Finally, verify that [Do Not Disturb], [Enable Call Forward], and [Block Anonymous Call] are not controlled by your phone system.
P
Paul WilsonAug 14, 2025
What to do if the STATUS indicator is flashing amber on my Panasonic KX-TGP500B04 Cordless Telephone?
- A
  Andrew OchoaAug 14, 2025
  If the STATUS indicator or indicator continues flashing in amber on your Panasonic Cordless Telephone, it could be due to an IP address not being acquired or the static IP address being inappropriate. If necessary, change the unit’s static IP address. Many installation issues can be resolved by resetting all the equipment. You may also need to check your network devices’ (router, modem, etc.) settings.
M
Mr. Arthur Walton IIAug 25, 2025
What to do if the STATUS indicator flashes amber rapidly on my Panasonic KX-TGP500B04 Cordless Telephone?
- A
  Adam FullerAug 25, 2025
  If the STATUS indicator or indicator flashes in amber rapidly on your Panasonic Cordless Telephone, even though the IP address was acquired, unplug the unit’s AC adaptor to reset it, then reconnect the AC adaptor. If the issue persists, contact your phone system dealer.
J
James AbbottSep 10, 2025
Why is the STATUS indicator amber when Ethernet is connected on my Panasonic Cordless Telephone?
- M
  Martin DownsSep 12, 2025
  If the STATUS indicator or indicator lights in amber on your Panasonic Cordless Telephone, even though the Ethernet cable is connected properly, the unit’s IP address may conflict with the IP addresses of other devices on your local network. If necessary, change the unit’s static IP address.

Panasonic KX-TGP500B04 Specifications

General

Type	Cordless Telephone
Frequency	1.9 GHz
DECT	Yes
VoIP	Yes
Protocols Supported	SIP
Handsets Supported	Up to 6
Speakerphone	Yes
Power Source	AC Adapter
Caller ID	Yes
Call Waiting	Yes
Intercom	Yes
Headset Jack	Yes
Range	Up to 300 meters outdoors
Battery Life	Up to 5 hours talk time
Display	1.8 inch