Chapter 4 Settings — [PROJECTOR SETUP] menu
172 - ENGLISH
*1 This item can be selected when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
*2 This item can be selected when the optional Function Board for 12G-SDI Optical (Model No.: TY-SB01FB) is installed in <SLOT>.
*3 This item can be selected when the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) is installed in <SLOT>.
*4 Individual input on the twisted‑pair‑cable transmitter or the DIGITAL LINK output supported device cannot be specied.
*5 This item can be selected when the optional Wireless Presentation System Receiver Board (Model No.: TY-SB01WP) is installed in <SLOT>.
*6 This item can be selected when the Function Board by other manufacturers is installed in <SLOT>.
Note
f When the [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set to
anything other than [OFF], the secondary input switching function will not operate even when [SECONDARY INPUT] is set to anything other
than [OFF]. The backup input switching function is prioritized.
[BACK COLOR]
Set the display of the screen when a signal is not input.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3) Press as to select [BACK COLOR].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[BLUE]
Displays blue in the entire screen.
[BLACK]
Displays black in the entire screen.
[DEFAULT LOGO]
Displays the Panasonic logo in the screen.
[USER LOGO]
Displays the image registered by the user in the screen.
Note
f The [BACK COLOR] setting item is common with the following menu item.
g The [DISPLAY OPTION] menu → [BACK COLOR]
f To create and register the [USER LOGO] image, use “Logo Transfer Software”. The software can be downloaded from the following website.
https://panasonic.net/cns/projector/
When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for “NO
SIGNAL SLEEP” of the DIGITAL LINK output supported device should be set to “OFF” to avoid interruption of communication.
[NO SIGNAL LIGHTS-OUT]
This is a function to automatically turn o the light source of the projector when there is no input signal for specic
period. The time until the light source is turned o can be set.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3) Press as to select [NO SIGNAL LIGHTS-OUT].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[DISABLE]
Disables the no signal lights-out function.
[10SEC.] - [5MIN.]
Turns o the light source when there is no input signal for the preset period.
Select [10SEC.], [20SEC.], [30SEC.], [1MIN.], [2MIN.], [3MIN.], or [5MIN.].
Note
f The [NO SIGNAL LIGHTS-OUT] setting item is common with the following menu item.
g The [PROJECTOR SETUP] menu → [POWER MANAGEMENT] → [NO SIGNAL LIGHTS-OUT]
f The fan will rotate to cool the projector while the no signal lights‑out function is operating and the light source is turned o. Also, the power
indicator <ON (G)/STANDBY (R)> blink green slowly.
f When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on
again from the condition that the light source has turned o by this function.
g When the signal is input
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the <POWER ON> button is pressed
To Next Page