Parker H Series - Page 18

Introduction
Follow these instructions when installing, operating, or servicing the
product.
H Series Fieldbus PROFIBUS Adapter,
Series A
(PSSCPBA)
The sealed IP67 housing of these adapters requires no enclosure.
(Note that environmental requirements other than IP67 may require
an additional appropriate housing.) PROFIBUS connectors are
sealed M12 (micro) style. The PROFIBUS adapter is shown below.
Installation & Service Instructions
E102P
H Series Fieldbus PROFIBUS
Adapter, Series A (PSSCPBA)
ISSUED: February, 2016
Supersedes: April, 2007
Doc.# E102P, EN# 160064, Rev. E
Pneumatic Division
Richland, Michigan 49083
Profibus Out
PSSCPBA
Profibus DP
Adapter
Status
Profibus
Status
PointBus
Status
System
Power
Adapter
Power
Profibus In
X10
PWR
X1
Shielding
(See page 3 for details)
PSSCPBA
M12 Connector
Mini 7/8"
Auxiliary
Power
Connector
Station
Address
Switches
H Series Fieldbus PROFIBUS Adapter User
Manual
The H Series Fieldbus PROFIBUS Adapter User Manual PSS-UM002A-
EN-P is not available at this time. Please refer to Rockwell Automation
1734 POINT I/O PROFIBUS Adapter User Manual 1734-UM005B-EN-P
for similar setup information, which is available online at
http://literature.rockwellautomation.com/.
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE
PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED
ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY
DAMAGE.
This document and other information from Parker Hannifin Corporation,
its subsidiaries and authorized distributors provide product and/or system
options for further investigation by users having technical expertise. It
is important that you analyze all aspects of your application, including
consequences of any failure and review the information concerning the
product or systems in the current product catalog. Due to the variety of
operating conditions and applications for these products or systems, the
user, through its own analysis and testing, is solely responsible for making
the final selection of the products and systems and assuring that all
performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product
features, specifications, designs, availability and pricing, are subject to
change by Parker Hannifin Corporation and its subsidiaries at any time
without notice.
EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION
IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE THESE PRODUCTS.
CONTACT YOUR LOCAL REPRESENTATIVE.
!
Safety Guide
For more complete information on recommended application guidelines, see
the Safety Guide section of Pneumatic Division catalogs or you can download
the Pneumatic Division Safety Guide at: www.parker.com/safety
WARNING
To avoid unpredictable system behavior that can cause personal injury
and property damage:
• Disconnectelectricalsupply(whennecessary)beforeinstallation,
servicing, or conversion.
• Disconnectairsupplyanddepressurizeallairlinesconnectedto
this product before installation, servicing, or conversion.
• Operatewithinthemanufacturer’sspeciedpressure,temperature,
and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below
freezing.
• Serviceaccordingtoprocedureslistedintheseinstructions.
• Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical
supplies(whennecessary)shouldbeconnectedandtheproduct
tested for proper function and leakage. If audible leakage is present,
or the product does not operate properly, do not put into use.
• Warnings and specifications on the product should not be
covered by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
!