Peavey IPA 300T - Fuse (7); Outputs (8); Rca Input Jack (9); A Input Jack (10)

FUSE (7)
T'd fuse IS located wilhm tlie cap c/ the fu$eholcter If the
iLse should ^ii. iT MUST BE REPLACED WrTH THE SAME
TYPE AN D \ALU EIN ORDER TO AVOID DAMAGE TO TH E
EQUIPMENT AND TO PREVENT VOIDING THE Vi^RRAN-
TV If 1 he amp repeated^ Wows fuses. i1 should be taken
(a a qualified service center lor reoair
WARNING* [HE FUSE SHOULD ONLY BE REPLACED
WHEN THE POWER CORD HAS BEEN DISCONNECTED
FROM ITS POWER SOURCE
OUTPUTS (8)
A direct oulpul, as well as several Iransformer outputs, are
pwided to aJIow 1^e p'C()er Interface between the ampiiiier
and tne speaker gysiem The direct output attows direct con¬
nection (0 a A ohm speaker sysfem. Tb use the output,
disconnect the jumper between the A 0 terminal and the
XF W R term ina. C onnect the s peaker (or s peakers) Irom thg
COM tarmlrai to the ^ C terminal 8 ohm. 2$ volt and to
volt balanced ouipufs are also prcpviOed, To use theso oi^«
puts, the lurfiper between 4 Q end KFMR must be inslall
ed. For 8 ohm speaker systems, connect between the COM
terminal and the 8 onm terminal. 25V and 70V ouiputs are
a ISO p/ovided for ''constant vo'iage' speaker disinoutior
systems. The 25V output connectiori is between the COM
terminal and the 25 V terminal The 7DV out pul connection
fe between the COM lerrmnal and rhe 70V terminal. One
more output is prc^^ided on the 'PA Senas amplifiers. This
B a balanoeO, trar>sformer isolated hne level output that is
provided for direct connection to “music on hold' systems,
booster power ampHlers, etc. This ou^ut is designed to
del iver 1V R MS into a 600 ohm loaa. See 'ig ures 5 ih rough
8 for pos&pie output cor^nectpns
RCA INPUT JACK (9)
Tne RCA line input ts paralle'ed with other inputs. See Tgure
4 concerning use o1 this jack
'A" INPUT JACK (10)
The V*" phorte Inputallcrtvs balanced mperstion (RTS) Thts
jack serves as an unbalanced input when used wjih a
“mono' (tip'Sieeve) V*" plug.
BALANCED INPUT (XLR) (11)
Tr>e baJarwed mput is in parallel 'W«n other inputs and allows
balanced opa'ation wilh XLR connection
UNE INPUTS (12)
The input terminals are contoured to allow balanced or un¬
balanced signals to be cor^neded to the system See figures
I and 2.
EXTERNAL MASTER VOLUME (IS)
T hese term mats at low connection of an ex® rnal voiume con-
irol. To gain complete control of volume Irom an externa
volume control, the hont pane) ‘imY control must be set
to maximum The external vdums control should oe con*
nected as shown in figure Z
INSTALLATION INFORMATION
POWER HANDLING AND GROUNDING:
For your satety, we ha^e incorporated a3-wire line (mans)
ceole wiffi 0 roper 3 founding fadities. It isixitadvsable to
remove the ground pin under any circumstances (f it is
necessary to use the ©Quipment wlhoui proper grounding
tacrrties, suftaOle grounding adaptors should be used Less
nurse and great'y reduced shod^ hazard exists when ihe
unit is operated with the prop^ grounded receplaces
ARCHITECTURAL & ENGINEERING
SPECIFICATIONS
The power amptifler shall have one input with provisions
for balanced ard ur balancedsigna's. Connections for the
baiancediAputahail beprovded viaar (RTS) Vi" lac^. XLR
“cannon*' jack, and barrier strip connections. Connections
ter the imbalanced input shall be provided by the (RTS) Vi "
jack barrier strip connections, and an RCA phono jack
Provison tor an external master volume control shaU be
made vb barrier strip connections on the back panel The
unit shall be packaged .n a rugged rnetai ohaasis 'B" v/ide
by 5’4t" high by 13deep (Inciuding external handles)
Tne unit shar operate Irom siancard 120 '^Its AC, 60 Hr
power The power amj^ifier shall be capable of delivering
300 warts Into 4 ohms and 8 ohms, as well as providing
25 volt rated powe< and 70 volt line culpuls. The un'rt shal'
be capable of doWering 40 Hzio 20 \<H 2 +0M dB into 4
orims at its direct outpul at . 1 % or less dieioruon with system
hum and rose al least 95 dB below raled output. The unit
shall be caHeo the Peavey Archifeciural Acoustics Division
moOe- IPA SOOT.
Rated Power & Load Direct Output:
300W RMS @ 4 ohms
Transformer Output (Fully leoiated)
300W RMS @ 16 ohms (70V);2 ohms (25V)
Distortion;
01% THD @ rated powei
Frequency Response Direct Output:
-hO/.l dB 40 Hz to 20 kHz
Hum & Norse
Greater tf^n 35 dB below raled power
Input Sensitivity
1.0V RMS
Subsonic Filter
Provides an 18 dB per octave roll off of low
irequencies wnn the 3 dB point at 42 Hz