What to do if Pentair AUTOTROL 368 salt tank is overflowing?
If the salt tank is overflowing, ensure all salt line connections are tight. Another possible cause is a drain line restricted with debris, so you should clean the drain control.
Why flow indicator on Pentair AUTOTROL 368 controller does not display service flow?
If the flow indicator on your Pentair Control Unit controller isn't displaying service flow, first ensure the bypass valve is not in the bypass position. If it isn't, check if the meter cable is fully inserted into the valve. If the problem persists, the meter might be clogged with debris, requiring you to remove and clean it.
What to do if Pentair AUTOTROL 368 drips water after regeneration?
If you observe flowing or dripping water at the drain or brine line after regeneration in your Pentair Control Unit, it could be because debris is preventing the #3 or #4 valve disc from closing. Remove the debris. Alternatively, the #3 or #4 valve disc might be worn and need replacement.
Why am I running out of conditioned water between regenerations with my Pentair AUTOTROL 368?
If you're running out of conditioned water between regenerations with your Pentair Control Unit, it's possible that the controller is improperly programmed. Verify the salt dosage and regeneration interval settings.
What to do if I see flowing or dripping water at drain or brine line after regeneration in Pentair AUTOTROL 368 Control Unit?
If you're experiencing flowing or dripping water at the drain or brine line after regeneration with your Pentair Control Unit, it's likely due to debris preventing valve disc #3 or #4 from closing properly. Remove any debris that you find. If the issue continues, the valve discs may be worn and need replacement.
What does error E1 mean on my Pentair AUTOTROL 368?
If your Pentair Control Unit displays 'E 1', it indicates that the program settings have been corrupted. Press any button. If “E 1” does not clear, replace the controller.
Why is there intermittent brine draw in my Pentair AUTOTROL 368 Control Unit?
If your Pentair Control Unit is experiencing intermittent brine draw, it could be due to low water pressure. Maintain a minimum pressure of 1.3 bar (20 psi).
Why flow indicator on Pentair AUTOTROL 368 Control Unit does not display service flow?
If the flow indicator on your Pentair Control Unit isn't displaying service flow, it could be because the bypass valve is in the bypass position. Remove the bypass valve from the bypass position. Another potential cause is the meter cable being dislodged from the valve; fully insert the meter cable into the valve. Lastly, the meter might be clogged with debris, in this case, remove and clean the meter.
Why is there no conditioned water after regeneration in my Pentair AUTOTROL 368 Control Unit?
If your Pentair Control Unit has no conditioned water after regeneration, it could be due to a lack of brine in the brine tank. Make sure to add brine to the brine tank. Alternatively, the injector might be plugged; clean the injector and screen.
What to do if Pentair AUTOTROL 368 Control Unit will not draw brine?
If your Pentair Control Unit isn't drawing brine, it might be due to a restricted drain line, so remove the restriction. Another possibility is a plugged injector; clean the injector and screen. Also, check if any debris is preventing the valve discs from closing and remove any foreign matter.
General| Model | AUTOTROL 368 |
|---|---|
| Type | Control Unit |
| Control Type | Electromechanical |
| Electromechanical | Yes |
| Power Supply | 120/240V AC |
| Voltage | 120/240V AC |
| Frequency | 50/60 Hz |
Details initial settings for installation including resin type, volume, and tank size.
Covers hydraulic parameters like injector size and refill controller number.
Specifies electrical parameters such as voltage and frequency.
Includes settings related to time of day, regeneration dosage, and capacity.
Defines the purpose and scope of the user guide, excluding installer information.
Provides manufacturer details, product model, and lists applicable norms and technical standards.
Details document release history and outlines Pentair's limitations of liability.
Identifies the location of safety tags on the device and ensures their legibility.
Addresses potential hazards, required personnel qualifications, and material safety precautions.
Recommends contact with dealer for sanitization and annual system disinfection.
Specifies the hydrostatic and working pressure, and the operational water temperature range.
Details acceptable environmental conditions including voltage, temperature, and humidity.
Guides through setting the time of day, brine dosage, and regeneration intervals.
Details how to set the desired capacity for regeneration for 606 controllers.
Explains setting days between regenerations for regulatory needs or flow sensor failure.
Recommends using EN973 certified salt pellets and avoiding rock or ice melt salts.
Notes that sanitizing may introduce chlorine, affecting resin life, requiring checks.
Initiates an immediate regeneration cycle, indicated by a cascading symbol.
Sets a delayed regeneration to occur at the next scheduled time, indicated by a blinking regen dot.
Allows skipping regeneration cycles to return the controller to service position.
Guides users on collecting information and contacting local dealers for technical assistance.
To Next Page
