Pentair AUTOTROL 368 - User Manual

Other manuals for Pentair AUTOTROL 368

Installer Manual60 pages

Service Manual20 pages

Questions and Answers:

M
Michael CurrySep 4, 2025
What to do if there's hard water leakage after recharge with Pentair Control Unit?
- C
  Christopher JosephSep 4, 2025
  If you notice hard water leakage after recharge, there are a few potential causes. First, the recharge might have been improper, so repeat the recharge, ensuring the correct salt dosage is set. Second, the external bypass valve might be leaking, in which case you should replace it. Finally, the O-ring around the riser pipe could be damaged, so replace the O-ring.
F
Felicia HensonSep 3, 2025
Why Pentair AUTOTROL 368 Control Unit will not draw salt?
- R
  Robert GreerSep 3, 2025
  If the control unit won't draw salt, it could be due to several reasons. First, check for a restricted drain line and remove any obstructions. Second, the injector might be plugged, so clean the injector and screen. Finally, debris might be preventing the valve discs from closing; if so, remove any foreign matter from the valve discs.
V
vangsamanthaSep 2, 2025
What to do if Pentair AUTOTROL 368 salt tank is overflowing?
- R
  Rachel BrooksSep 3, 2025
  If the salt tank is overflowing, ensure all salt line connections are tight. Another possible cause is a drain line restricted with debris, so you should clean the drain control.
V
Victoria PenaSep 2, 2025
What does error E1 mean on Pentair Control Unit?
- S
  salinaswillieSep 2, 2025
  If your Pentair Control Unit displays "E 1", press any button. If "E 1" does not clear, replace the controller, as the program settings have been corrupted.
A
Angela CookeAug 31, 2025
What to do if Pentair AUTOTROL 368 drips water after regeneration?
- D
  donald83Aug 31, 2025
  If you observe flowing or dripping water at the drain or brine line after regeneration in your Pentair Control Unit, it could be because debris is preventing the #3 or #4 valve disc from closing. Remove the debris. Alternatively, the #3 or #4 valve disc might be worn and need replacement.
J
James MooreAug 30, 2025
Why Pentair AUTOTROL 368 Control Unit runs out of conditioned water between regenerations?
- K
  kathleen87Aug 30, 2025
  If you run out of conditioned water between regenerations with your Pentair Control Unit, the controller might be improperly programmed. Verify the salt dosage and regeneration interval settings.
J
Jeremy MillsAug 29, 2025
What causes brine tank overflow in Pentair Control Unit?
- J
  Julie CampbellAug 29, 2025
  If your Pentair Control Unit is overflowing the brine tank, ensure all brine line connections are tight. Also, the drain line might be restricted with debris; clean the drain controller.
C
Christopher BrightAug 28, 2025
Why Pentair AUTOTROL 368 backwashes at excessively low rate?
- V
  Victoria TurnerAug 28, 2025
  If your Pentair Control Unit is backwashing or purging at an excessively low or high rate, it might be due to an incorrect drain controller being used. Replace it with the correct size controller. Another cause could be the absence of a drain line flow controller; install a drain line flow controller. A restricted drain line could also be the culprit; remove the restriction.
C
Cindy RobertsAug 27, 2025
Why is there intermittent brine draw in my Pentair AUTOTROL 368 Control Unit?
- W
  Willie NguyenAug 27, 2025
  If your Pentair Control Unit is experiencing intermittent brine draw, it could be due to low water pressure. Maintain a minimum pressure of 1.3 bar (20 psi).
S
Sydney CobbAug 27, 2025
Why flow indicator on Pentair AUTOTROL 368 Control Unit does not display service flow?
- J
  Joseph BarkerAug 27, 2025
  If the flow indicator on your Pentair Control Unit isn't displaying service flow, it could be because the bypass valve is in the bypass position. Remove the bypass valve from the bypass position. Another potential cause is the meter cable being dislodged from the valve; fully insert the meter cable into the valve. Lastly, the meter might be clogged with debris, in this case, remove and clean the meter.