Pentair BLUEFURY LITE

Questions and Answers

D
Daniel Scott MDAug 16, 2025
What to do if Pentair Pressure Washer will not climb?
- E
  Edward KingAug 16, 2025
  If your Pentair Pressure Washer won't climb, check the debris bag and empty it if it's full. Ensure proper water flow by calculating the cleaner speed/RPM and adjust the flow at the wall fitting if needed. Note that the climbing ability depends on pool shape and available water flow, performing better in pools without sharp angles or in the transition from the pool floor to the pool wall.
M
Maria PeckAug 20, 2025
How to fix Pentair Pressure Washer hoses tangling in loops?
- F
  Francisco TurnerAug 20, 2025
  To fix tangling hoses in your Pentair Pressure Washer, check the length of the feed hose, as a hose that is too long may cause tangling or looping. Ensure the feed hose floats on the pool surface with hose floats spaced about two feet apart. Make sure the hose swivels spin freely, and replace them if they are tight. Also, ensure the feed hose has no kinks or bends.
C
Charles CostaAug 25, 2025
What to do if Pentair Pressure Washer does not go in reverse?
- A
  Amanda WatsonAug 25, 2025
  If your Pentair Pressure Washer doesn't reverse, ensure the backup valve cycles approximately every 3-1/2 minutes to reposition the cleaner. Check for proper flow by calculating cleaner speed/RPM and adjust the flow at the wall fitting if needed. Also, make sure the wall fitting debris screen and the in-line filter’s debris screen are free of debris; remove and rinse if necessary.
T
Tina WestAug 28, 2025
Why is Pentair Pressure Washer booster pump very noisy?
- M
  Michele GonzalezAug 28, 2025
  If your Pentair Pressure Washer booster pump is very noisy, first, ensure that both the filter pump and booster pump are on and moving water. You may need to clean your pool filter system. Also, make sure the wall fitting is properly installed and, if leaking, the O-Ring may need to be replaced. If the issue persists, it may be a booster pump problem.
M
matthew40Aug 31, 2025
What to do if Pentair Pressure Washer cleaner hangs at steps?
- B
  Brandi CruzSep 1, 2025
  If your Pentair Pressure Washer cleaner hangs at the steps, make sure the backup valve cycles approximately every 3-1/2 minutes to reposition the cleaner. Check for proper flow by calculating cleaner speed/RPM and adjust the flow at the wall fitting if needed.
M
michaelramirezSep 5, 2025
Why Pentair Pressure Washer cleaner tilts to one side?
- J
  Jennifer BarberSep 5, 2025
  If your Pentair Pressure Washer cleaner tilts to one side, it usually indicates a full debris bag. Empty the debris bag. Note that the cleaner may tilt on one side (on two wheels) during a turn cycle; observe it for a few minutes to see if it rights itself.
C
Christopher WhiteSep 8, 2025
Why Pentair Pressure Washer rear wheels dragging or not spinning?
- B
  Brandon MillerSep 9, 2025
  If the rear wheels of your Pentair Pressure Washer are dragging or not spinning, make sure the wheel is free of tangled debris.
R
Ricky JohnsonNov 12, 2025
Why Pentair Pressure Washer cleaner doesn’t move or moves slowly?
- J
  James ShafferNov 12, 2025
  If your Pentair Pressure Washer cleaner isn't moving or is moving slowly, make sure the filter pump and booster pump are on and moving water; you might need to clean your pool filter system. Check that the wall fitting debris screen and the in-line filter's debris screen are free of debris; rinse if needed. Calculate the cleaner speed/RPM to check for proper flow and adjust the flow at the wall fitting if necessary. Also, inspect all feed hose connections and swivels for leaks. Remove any flow restrictor plate installed in the wall fitting adapter. Clear any debris jammed in the gear teeth of the front drive wheels by gently rotating them backward. Ensure the rear wheels spin freely, replacing them if necessary. Finally, confirm the backup valve cycles approximately every 3-1/2 minutes, re...