Why does my Pentair Control Unit show Motor Run-On Error /Cycle Sense Error?
The Motor Run-On Error /Cycle Sense Error on a Pentair Control Unit is a non-critical error caused by an extra optical sensor pulse. Press any button to clear the error. You can also press the extra cycle button to advance the motor and clear the error.
How to reset regeneration failure on Pentair Water Filtration System?
To reset a regeneration failure on your Pentair Water Filtration System, perform a manual regeneration.
Why does my Pentair Control Unit water softener fail to regenerate automatically?
If your Pentair Control Unit softener fails to regenerate automatically, ensure it's connected to a constant power source. Check the meter cable for disconnections or faults, reconnecting or replacing it as needed. If the power cord is defective, replace it. Also, examine the controller, meter, or sensor for defects and replace or repair them. Finally, verify that the unit is programmed correctly.
What to do if my Pentair Water Filtration System has excessive water in the brine tank and/or salty water to service?
If you notice excessive water in the brine tank or salty water being delivered, there might be a plugged drain line. Check the flow to the drain and clean the flow control. Another possible cause is a dirty or damaged brine valve, which should be cleaned or replaced. Also, inspect the injector for any blockages; clean the injector and replace the screen if necessary. Ensure that the inlet pressure is at least 1.4 bar to allow the injector to function correctly. Finally, if the timer isn't cycling, consider replacing the controller.
Why does my Pentair Water Filtration System have a loss of water pressure?
A loss of water pressure in your Pentair Water Filtration System can occur due to scaling or fouling of the inlet pipe. Clean or replace the pipeline and consider pretreatment to prevent future occurrences. Fouled resin can also cause this issue; clean the resin and pretreat to prevent it from happening again.
What to do if Pentair Control Unit regeneration fails?
To address a regeneration failure in your Pentair Control Unit, perform a manual regeneration to reset the error code. If the system is metered, verify that it is measuring flow by running service water and watching for the flow indicator on the display. If the unit doesn’t measure flow, verify that the meter is working properly and that the cable is well connected. Enter master programming mode and verify that the unit is configured properly, checking that the meter is identified correctly.
How to reduce high salt usage in my Pentair Control Unit?
To address high salt usage in your Pentair Control Unit, adjust the salt setting. Also, refer to the troubleshooting steps for "Excessive water in brine tank".
Why does the valve cycle continuously on my Pentair Control Unit?
If the valve cycles continuously on your Pentair Control Unit, replace the controller, as this indicates a faulty controller.
What causes continuous flow to drain in Pentair Water Filtration System?
Continuous flow to the drain in your Pentair Water Filtration System can be caused by a motor that stopped or jammed during regeneration, in which case you should replace the motor.
What to do if Pentair Water Filtration System valve cycles continuously?
If the valve of your Pentair Water Filtration System is cycling continuously, the controller may be faulty. In this case, replace the controller.
Configuration parameters related to the initial installation of the water treatment system.
Settings that define the hydraulic operation and flow characteristics of the device.
Parameters related to the electrical supply and requirements of the controller.
Configuration options for the controller's software, including regeneration modes.
Crucial safety precautions to be followed before handling or operating the system.
Information regarding the purpose and target audience of the user guide.
Details concerning the document's revision history and release information.
Details that identify the manufacturer and the specific product model.
List of directives and standards with which the product complies.
Statement outlining Pentair's warranty limitations and disclaimers.
Identification of the location and details of the serial label on the device.
Overview of general hazards, personnel qualifications, and material safety points.
Recommendations for maintaining system hygiene and periodic disinfection.
Key technical data including pressure, flow rate, and environmental operating conditions.
Details on the recommended environmental parameters for system operation.
Visual identification and location of key components on different controller types.
Instructions on how to bypass the water softening system during normal or fault conditions.
Specific requirements and considerations for installing the XTRi controller.
Guide to programming features and initial setup for XTRi and XTR controllers.
Steps for initial setup and quick start configuration of touchscreen controllers.
Procedure for setting a service interval based on months or regenerations.
Explanation of the main screen elements, status indicators, and navigation buttons.
Instructions for adjusting the current day, date, and time settings.
Accessing and configuring various system settings like Bluetooth and regeneration timing.
How to adjust the water hardness setting and its effect on regeneration intervals.
Procedure to enter and view diagnostic information on the controller.
Step-by-step guide for initial programming of the SXT controller.
How to set the current day of the week for regeneration scheduling.
Navigating through diagnostic data screens to view system information.
Instructions for basic programming of the LXT controller.
Accessing and navigating diagnostic data for the LXT controller.
Usage recommendations for salts and sanitizing processes for XTRI/XTR controllers.
Steps to initiate an immediate regeneration cycle for XTRI, XTR, and SXT controllers.
Guide on pairing the FLECK 5800 XTRI Connected Valve with Wi-Fi devices.
Usage recommendations for salts and sanitizing processes for LXT controllers.
List and descriptions of error codes that may appear on the SXT controller.
List and descriptions of error codes that may appear on the LXT controller.
Mandatory cleaning and maintenance procedures to ensure system functionality.
Procedure for obtaining technical support and troubleshooting common issues.
General| Brand | Pentair |
|---|---|
| Model | Fleck 5800 LXT |
| Type | Water Softener Control Valve |
| Control Head | Electronic |
| Valve Material | Noryl |
| Capacity | 48, 000 grains |
| Metered | Yes |
| Brine Line | 3/8" |
| Display | LCD |
| Operating Pressure | 20 - 125 psi |
| Operating Temperature | 34 - 120 °F |
| Inlet/Outlet | 1" |
| Drain Line | 1/2" |
| Backwash Capacity | 17 GPM |
| Backwash Flow Rate | 17 GPM |
| Regeneration Type | Demand Initiated |
| Cycle Times | Variable |
| Brine Draw Flow Rate | 0.5 GPM |
| Programming Options | Regeneration cycle sequence, cycle times, salt dosage, reserve capacity, calendar override |
To Next Page
