How to fix fail safe error on Pentair Water Filtration System?
To address a fail-safe error on your Pentair Water Filtration System, unplug the unit and plug it back in. If the error reoccurs, unplug the unit, put it into bypass, and contact your dealer.
What to do if my Pentair Water Filtration System softener fails to use salt?
If your Pentair Water Filtration System softener fails to use salt, begin by cleaning the drain line and/or flow control if they are plugged or restricted. Next, clean or replace the injector and screen if the injector is plugged. Check for any restrictions in the BLFC and ensure the safety float is not stuck if there is no water in the brine tank. Ensure the line pressure is at least 1.4 bar if the water pressure is too low. Check the brine line for air leaks if it injects air during brine draw.
What to do if Pentair Water Filtration System shows Regen Failure?
If your Pentair Water Filtration system displays a Regen Failure error, perform a manual regeneration to reset the error code. For metered systems, ensure it's measuring flow by running service water and checking the display's flow indicator. If no flow is measured, check the meter cable connection and meter functionality. In Master Programming Mode, verify the unit's configuration, valve configuration, system capacity, day override setting, and meter identification. For Day-of-Week systems, confirm at least one day is set to ON. Correct any settings as needed.
How to fix Motor Stall / Cam Sense Error in Pentair FLECK 5800 SXT?
To address a Motor Stall / Cam Sense Error in your Pentair Water Filtration System, try unplugging the unit and plugging it back in to allow the control to attempt to find its position again. Check that the optical sensor is correctly placed and wired to the circuit board. Make sure the motor and drive train components are in good shape and properly assembled. Inspect the valve to ensure the piston moves freely. Replace or reassemble components as needed. If the error persists after plugging it back in, unplug the unit, put it into bypass.
What to do if Pentair Water Filtration System shows Memory Error?
If your Pentair Water Filtration system is showing a Memory Error, perform a Master Reset and then reconfigure the system using the Master Programming Mode. After reconfiguring, manually step the valve through a regeneration cycle. If the error continues, call technical support.
How to fix motor stall error on Pentair Water Filtration System?
To troubleshoot a motor stall or cam sense error in your Pentair Water Filtration System, unplug the unit and plug it back in to allow the controller to attempt to find its position again. If it fails, unplug the unit, open the cover, and verify the optical sensor is in place with the wires connected to the circuit. Check the motor and gearing components for good condition and proper assembly. Verify the valve and ensure the piston travels freely. Replace or reassemble components as needed. If the error persists, unplug the unit, put it into bypass, and contact your dealer.
Why does the valve cycle continuously on my Pentair Water Filtration System?
If the Pentair Water Filtration System valve cycles continuously, the controller might be faulty. Replace the controller to resolve this issue.
What does motor run-ON error mean on Pentair Water Filtration System?
To address a motor run-ON error or cycle sense error on your Pentair Water Filtration System, note that this is a non-critical error, indicating an extra optical sensor pulse was detected. Press any button to clear the error, or press to advance the motor to clear it.
What to do if there's excessive water in the brine tank of my Pentair Water Filtration System?
To address excessive water in the brine tank or salty water, start by checking the flow to the drain and clean the flow control if necessary. Inspect and clean or replace the brine valve if it's dirty or damaged. Also, clean the injector and replace the screen. Ensure the inlet pressure is at least 1.4 bar for proper injector performance. If the timer isn't cycling, consider replacing it.
What to do if Pentair Control Unit displays Fail Safe Error?
If the Pentair Control Unit shows a Fail Safe Error, unplug the unit and plug it back in. If the error continues, contact technical support.
Details on controller, valve, resin, tank, and brine settings.
Configuration of hydraulic parameters like injector and flow controls.
Electrical specifications including voltage, frequency, and power.
Software parameters for regeneration start, interval, and cycle times.
Information on the purpose and intended use of the user guide.
Details on document revisions and publication history.
Identification of the manufacturer and the specific product model.
List of guidelines and technical standards the product complies with.
Disclaimer regarding warranty and manufacturer's responsibility.
Identifies the location of the serial label and its components on the device.
General warnings about potential injuries, property damage, or pollution.
Recommendations for system sanitization and water quality checks.
Key technical data including pressure, flow rate, and environmental conditions.
Operating conditions related to humidity, voltage, and temperature.
Visual guide to the device's components and their placement.
Procedure for bypassing the system during normal operation or in case of a problem.
Instructions for programming the XTRi and XTR controller.
Accessing and viewing diagnostic information for the controller.
Step-by-step guide for initial programming of the SXT controller.
Accessing and viewing diagnostic information for the controller.
Step-by-step guide for initial programming of the LXT controller.
Accessing and viewing diagnostic information for the controller.
Operational recommendations and procedures for XTRI and XTR controllers.
Guide to connecting the XTRI valve to Wi-Fi devices via the Pentair Home App.
Operational recommendations and procedures for the SXT controller.
Operational recommendations and procedures for the LXT controller.
Error codes and troubleshooting steps specific to XTRI and XTR controllers.
List of error codes and their corresponding solutions for SXT controllers.
List of error codes and their corresponding solutions for LXT controllers.
General| Brand | Pentair |
|---|---|
| Model | FLECK 5800 SXT |
| Category | Water Filtration Systems |
| Language | English |
To Next Page
