What causes poor water quality in Pentair FLECK 5800 SXT Water Filtration Systems?
If you notice poor water quality with your Pentair Water Filtration System, check the items listed in loss of capacity. Ensure the bypass valve is closed. Check for channeling due to too slow or high service flow, or media fouling. Set mixing correctly.
How to troubleshoot loss of water pressure in Pentair Water Filtration System?
If you experience a loss of water pressure in your Pentair Water Filtration System, start by cleaning or replacing the inlet pipe if it's scaled or fouled, and consider pretreatment to prevent future issues. Clean the resin if it's fouled, and pretreat to prevent. If backwash is improper, contact your dealer to reset the backwash flow rate and/or adjust the time, due to too many resin fines and/or sediment.
How to fix a Pentair Water Filtration System that fails to regenerate automatically?
To resolve a Pentair Water Filtration System softener that won't regenerate automatically, ensure the cord is connected to a constant power source. Check and reconnect or replace the meter cable if it's disconnected or faulty. Replace the power cord if it's defective. If the timer, meter, or sensor is defective, replace or repair it. Finally, ensure the system is programmed correctly.
Why does my Pentair Control Unit show Motor Run-On Error /Cycle Sense Error?
The Motor Run-On Error /Cycle Sense Error on a Pentair Control Unit is a non-critical error caused by an extra optical sensor pulse. Press any button to clear the error. You can also press the extra cycle button to advance the motor and clear the error.
What to do if Pentair Control Unit displays Fail Safe Error?
If the Pentair Control Unit shows a Fail Safe Error, unplug the unit and plug it back in. If the error continues, contact technical support.
How to fix Motor Stall /Cam Sense Error on Pentair Control Unit?
If the Pentair Control Unit displays a Motor Stall /Cam Sense Error, unplug the unit and plug it back in, allowing it to attempt to find its position again. Check that the optical sensor is correctly placed and wired to the circuit board. Ensure the motor and drive train are in good condition and properly assembled. Inspect the valve to confirm the piston moves freely. Replace or reassemble components as needed. If the error persists, unplug the unit, put it into bypass, and contact technical support.
What to do if Pentair Control Unit shows Regen Failure?
If the Pentair Control Unit hasn't regenerated in 30 days, perform a manual regeneration to clear the error. For metered systems, check if it's measuring flow by observing the display's flow indicator while running service water. If no flow is measured, ensure the meter cable is correctly connected and functioning. Access Master Programming Mode to confirm the unit's configuration matches the valve setup and that the appropriate system capacity and meter size are selected.
Why does my Pentair Water Filtration System show Fail Safe Error?
If your Pentair Water Filtration System displays a Fail Safe Error, it means the valve failed to find its position within one minute. Unplug the unit, then plug it back in. If the error continues, call technical support.
What does Motor Run-On Error mean on Pentair Water Filtration System and how to clear it?
A Motor Run-On Error (Cycle Sense Error) on your Pentair Water Filtration System indicates a non-critical issue where an extra optical sensor pulse was detected. To clear this error, simply press any button. Alternatively, press the extra cycle button to advance the motor.
What to do if Pentair Water Filtration System shows Memory Error?
If your Pentair Water Filtration system is showing a Memory Error, perform a Master Reset and then reconfigure the system using the Master Programming Mode. After reconfiguring, manually step the valve through a regeneration cycle. If the error continues, call technical support.
General| Brand | Pentair |
|---|---|
| Model | FLECK 5800 SXT |
| Category | Water Filtration Systems |
| Language | English |
Details on controller, valve, resin, tank, and brine settings.
Configuration of hydraulic parameters like injector and flow controls.
Electrical specifications including voltage, frequency, and power.
Software parameters for regeneration start, interval, and cycle times.
Information on the purpose and intended use of the user guide.
Details on document revisions and publication history.
Identification of the manufacturer and the specific product model.
List of guidelines and technical standards the product complies with.
Disclaimer regarding warranty and manufacturer's responsibility.
Identifies the location of the serial label and its components on the device.
General warnings about potential injuries, property damage, or pollution.
Recommendations for system sanitization and water quality checks.
Key technical data including pressure, flow rate, and environmental conditions.
Operating conditions related to humidity, voltage, and temperature.
Visual guide to the device's components and their placement.
Procedure for bypassing the system during normal operation or in case of a problem.
Instructions for programming the XTRi and XTR controller.
Accessing and viewing diagnostic information for the controller.
Step-by-step guide for initial programming of the SXT controller.
Accessing and viewing diagnostic information for the controller.
Step-by-step guide for initial programming of the LXT controller.
Accessing and viewing diagnostic information for the controller.
Operational recommendations and procedures for XTRI and XTR controllers.
Guide to connecting the XTRI valve to Wi-Fi devices via the Pentair Home App.
Operational recommendations and procedures for the SXT controller.
Operational recommendations and procedures for the LXT controller.
Error codes and troubleshooting steps specific to XTRI and XTR controllers.
List of error codes and their corresponding solutions for SXT controllers.
List of error codes and their corresponding solutions for LXT controllers.
To Next Page
