How to fix high salt usage in Pentair Water Filtration System?
If your Pentair Water Filtration System is using too much salt, first adjust the salt setting. Also, check for excessive water in the brine tank.
What causes poor water quality in my Pentair Water Filtration System?
Poor water quality from your Pentair Water Filtration System may be due to an open bypass valve; ensure it is closed. Channeling can also cause this, so check for service flow that is either too slow or too high, and inspect for media fouling. Finally, verify that the mixing is set correctly.
Why does my Pentair Water Filtration System have a loss of water pressure?
A loss of water pressure in your Pentair Water Filtration System can occur due to scaling or fouling of the inlet pipe. Clean or replace the pipeline and consider pretreatment to prevent future occurrences. Fouled resin can also cause this issue; clean the resin and pretreat to prevent it from happening again.
What to do if my Pentair Water Filtration System has excessive water in the brine tank and/or salty water to service?
If you notice excessive water in the brine tank or salty water being delivered, there might be a plugged drain line. Check the flow to the drain and clean the flow control. Another possible cause is a dirty or damaged brine valve, which should be cleaned or replaced. Also, inspect the injector for any blockages; clean the injector and replace the screen if necessary. Ensure that the inlet pressure is at least 1.4 bar to allow the injector to function correctly. Finally, if the timer isn't cycling, consider replacing the controller.
Why does my Pentair Control Unit water softener fail to regenerate automatically?
If your Pentair Control Unit softener fails to regenerate automatically, ensure it's connected to a constant power source. Check the meter cable for disconnections or faults, reconnecting or replacing it as needed. If the power cord is defective, replace it. Also, examine the controller, meter, or sensor for defects and replace or repair them. Finally, verify that the unit is programmed correctly.
What to do if my Pentair Water Filtration System softener fails to use salt?
If your Pentair Water Filtration System softener isn't using salt, start by cleaning the drain line and/or flow control if they are plugged or restricted. Next, inspect the injector; clean or replace it and the screen if plugged. Also, check for any restrictions in the BLFC and ensure the safety float is not stuck if there's no water in the brine tank. The line pressure must be at least 1.4 bar. Check the brine line for air leaks if it injects air during brine draw.
What causes poor water quality in Pentair Control Unit?
General| Brand | Pentair |
|---|---|
| Model | Fleck 5800 LXT |
| Type | Water Softener Control Valve |
| Control Head | Electronic |
| Valve Material | Noryl |
| Capacity | 48, 000 grains |
| Metered | Yes |
| Brine Line | 3/8" |
| Display | LCD |
| Operating Pressure | 20 - 125 psi |
| Operating Temperature | 34 - 120 °F |
| Inlet/Outlet | 1" |
| Drain Line | 1/2" |
| Backwash Capacity | 17 GPM |
| Backwash Flow Rate | 17 GPM |
| Regeneration Type | Demand Initiated |
| Cycle Times | Variable |
| Brine Draw Flow Rate | 0.5 GPM |
| Programming Options | Regeneration cycle sequence, cycle times, salt dosage, reserve capacity, calendar override |
Configuration parameters related to the initial installation of the water treatment system.
Settings that define the hydraulic operation and flow characteristics of the device.
Parameters related to the electrical supply and requirements of the controller.
Configuration options for the controller's software, including regeneration modes.
Crucial safety precautions to be followed before handling or operating the system.
Information regarding the purpose and target audience of the user guide.
Details concerning the document's revision history and release information.
Details that identify the manufacturer and the specific product model.
List of directives and standards with which the product complies.
Statement outlining Pentair's warranty limitations and disclaimers.
Identification of the location and details of the serial label on the device.
Overview of general hazards, personnel qualifications, and material safety points.
Recommendations for maintaining system hygiene and periodic disinfection.
Key technical data including pressure, flow rate, and environmental operating conditions.
Details on the recommended environmental parameters for system operation.
Visual identification and location of key components on different controller types.
Instructions on how to bypass the water softening system during normal or fault conditions.
Specific requirements and considerations for installing the XTRi controller.
Guide to programming features and initial setup for XTRi and XTR controllers.
Steps for initial setup and quick start configuration of touchscreen controllers.
Procedure for setting a service interval based on months or regenerations.
Explanation of the main screen elements, status indicators, and navigation buttons.
Instructions for adjusting the current day, date, and time settings.
Accessing and configuring various system settings like Bluetooth and regeneration timing.
How to adjust the water hardness setting and its effect on regeneration intervals.
Procedure to enter and view diagnostic information on the controller.
Step-by-step guide for initial programming of the SXT controller.
How to set the current day of the week for regeneration scheduling.
Navigating through diagnostic data screens to view system information.
Instructions for basic programming of the LXT controller.
Accessing and navigating diagnostic data for the LXT controller.
Usage recommendations for salts and sanitizing processes for XTRI/XTR controllers.
Steps to initiate an immediate regeneration cycle for XTRI, XTR, and SXT controllers.
Guide on pairing the FLECK 5800 XTRI Connected Valve with Wi-Fi devices.
Usage recommendations for salts and sanitizing processes for LXT controllers.
List and descriptions of error codes that may appear on the SXT controller.
List and descriptions of error codes that may appear on the LXT controller.
Mandatory cleaning and maintenance procedures to ensure system functionality.
Procedure for obtaining technical support and troubleshooting common issues.
To Next Page
