EasyManuals Logo

Pentair MasterTemp 250 User Manual

Pentair MasterTemp 250
172 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
Rev. N 10/2018 MASTERTEMP Pool and Spa Heater Installation and User’s Guide
21
VENT INSTALLATION – INDOOR INSTALLATION (US AND CANADA)
(Category I)
Always vent the heater to the outdoors, see Note*.
Vent it vertically using Type “B” double wall vent connector pipe.
Locate the heater so as to minimize the length of horizontal venting and the number of vent elbows required. Horizontal
vent runs must slope up 1/4-in per foot (2cm/M) from the heater to allow exhaust condensate to drain and it is recommended
to have a condensate drain as described in the venting installation instructions.
VERTICAL VENTING
- NEGATIVE PRESSURE
(See Figures 11, 12 and 13)
Vent the heater vertically in a negative pressure (positive draft) system in
accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 and/or
CSA B149.1, Natural Gas and Propane Installation Codes, and local codes. Type
“B” Double-wall vent connector is recommended; however single-wall pipe is
allowed by the National Fuel Gas Code in some circumstances. Consult your
local code official for detailed information. Do not use a draft hood with this heater.
To connect a negative pressure metal gas vent to the heater, order the appropriate
Metal Flue Collar from the chart below:
Section 3. Installation Instructions
C
o
m
b
us
ti
o
n
C
hambe
r
Flue Collar
4" x 8" Metal
Flue Collar
V
ent Bod
V
V
C
lean the Interior Surface
Vent Pipe
C
lean and RTV
This
S
u
r
face
Figure 11.
1. See Table 7, to determine allowable vent sizes for your heater.
NOTICE: Table 7 is for installations in which the total lateral vent length (that is, the horizontal distance from the flue
collar to the main vertical portion of the vent) is less than 1/2 the total vent height (the vertical distance from the flue collar
to the vent termination) and which have three or less elbows in the system. For venting systems which do not meet these
conditions, consult the National Fuel Gas Code, ANSI Z223.1 (U.S.), or the standards CSA B149.1 and B149.2 (Canada).
Read “VERTICAL VENTING – NEGATIVE PRESSURE” before using this table.
Table 7.
– Permitted Minimum and Maximum Vent Heights By Size and Heater Model
NOTE *: Vent must be at least eight (8) feet away from
nearest vertical surface. Vents extending five (5) feet or
more above the roof must be braced or guyed.
Consult your local code officials for detailed information.
ralloCeulFlateM.oNtraP
"6x46700-70777
"8x47700-70777
)sreteM(teeFnirotcennoCllaW-elbuoD"B"epyThtiwtneVllaW-elbuoD"B"epyT
eziStneV
571ledoM
.xam/.nimthgieH
002ledoM
.xam/.nimthgieH
052ledoM
.xam/.nimthgieH
003ledoM
.xam/.nimthgieH
004ledoM
.xam/.nimthgieH
.ni6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)5.5(.tf81)5.03(.tf001/)9(.tf03.ceRtoN
.ni7)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)4.2(.tf8)5.03(.tf001/)3(.tf01)5.03(.tf001/)6.4(.tf51
.ni8)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)4.2(.tf8
.ni01dna9)3.51(.tf05/)8.1(.tf6)3.51(.tf05/)8.1(.tf6)3.51(.tf05/)8.1(.tf6)5.03(.tf001/)8.1(.tf6)5.03(.tf001/)8.1(.tf6
)sreteM(teeFnirotcennoCllaW-elgniShtiwtneVllaW-elbuoD"B"epyT
eziStneV
571ledoM
.xam/.nimthgieH
002ledoM
.xam/.nimthgieH
052ledoM
.xam/.nimthgieH
003ledoM
.xam/.nimthgieH
004ledoM
.xam/.nimthgieH
.ni6)6.4(.tf51/)8.1(.tf6)6.4(.tf51/)8.1(.tf6)6.4(.tf51/)8.1(.tf6.ceRtoN.ceRtoN
.ni7)4.2(.tf8/)8.1(.tf6)4.2(.tf8/)8.1(.tf6)4.2(.tf8/)8.1(.tf6)6(.tf02/)3(.tf01)3.51(.tf05/)6.4(.tf51
.ni8.ceRtoN.ceRtoN.ceRtoN)6(.tf02/)8.1(.tf6)6(.tf02/)4.2(.tf8
.ni9.ceRtoN.ceRtoN.ceRtoN.ceRtoN)8.1(.tf6/)8.1(.tf6
.ni01.ceRtoN.ceRtoN.ceRtoN.ceRtoN.ceRtoN

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Pentair MasterTemp 250 and is the answer not in the manual?

Pentair MasterTemp 250 Specifications

General IconGeneral
BTU Output250, 000 BTU/hr
Fuel TypeNatural Gas or Propane
Efficiency82%
IgnitionElectronic
ModelMasterTemp 250
Minimum Water Flow20 GPM
Max Working Pressure50 psi
Water Connections2-inch
CertificationsANSI Z21.56
Voltage120 VAC

Related product manuals