2-8
19
English
To erase the entire programme
● Press Ç once when playback is stopped or
twice during playback.
➜ "PROGRAM CLEARED" will be displayed.
➜
PROG
will disappear from the display.
Note:
– The programme will be erased if you change
source, select another disc tray, disconnected the
system from the power supply or when the disc
tray is opened.
Repeat
You can play the current track/disc/programme
repeatedly during playback.
1
Press REPEAT on the remote control
repeatedly to select various repeat modes.
● In normal playback
➜ "REPEAT TRACK" – to repeat the current
track.
"REPEAT DISC" – to repeat the entire disc.
➜
RPT
appears on the display.
● In programme playback
➜ "REPEAT TRACK" – to repeat the current
programmed track.
"REPEAT PROGRAM" – to repeat all
programmed tracks.
➜
RPT
and
PROG
will appear on the display.
● The current track/disc/programme will now be
played repeatedly until you press Ç.
2
To resume normal playback, press REPEAT
until the "REPEAT OFF" mode is displayed.
➜
RPT
will disappear from the display.
CD/VCD/MP3-CD Operation
Title/Album Name
This feature use to display the title and album
name for MP3-CD.
● Press TITLE/ALBUM NAME repeatedly to
display the title or album name.
➜
TITLE
will start flashing if title name is
displayed.
➜
ALB
will start flashing if album name is
displayed.
For Recording, please refer to “Tape
Operation/Recording”.
20
English
OSD – On Screen Display
If you insert VCD, your TV screen will serve as an
additional display for messages (e.g. PLAY, STOP),
and information stored on the VCD.
● Press OSD on the remote control repeatedly to
switch on or off the On Screen Display.
When OSD is switched ON; you can see the
following display on the TV screen.
Below is an example of the OSD message.
SINGLE ELAPSED
PLAY XX/TT MM:SS
–"XX" is the current track.
–"TT" is the total tracks.
–"MM" is in minutes.
–"SS" is in seconds.
Note:
–You can also view the information from a
MP3-CD or normal CD.
Playing a Video CD with PBC
VCD with PBC (Playback Control) will be
indicated on the display of the set as soon as
they are inserted. PBC is a predefined play
sequence stored on the VCD.
1
Switch on the TV, insert a VCD with PBC and
press PLAYÉÅ to start playback.
2
MENU appears on the TV screen.
If the menu consists of a list of titles, you
can select a sequence directly
● Press Digits 0–9 on the remote control to
select your choice.
➜ The VCD starts playing of the selected
sequence automatically.
Note:
– If a menu consists of more than one page, press
¡
/
™
to go through the pages.
Switching off PBC
● In stop mode, press PBC.
➜ “PBC OFF” will be displayed.
Notes:
–Programme mode is not available whenever PBC
mode is switched on.
– The menu structure depends on the information
stored on the VCD. Please refer to the information
supplied with the disc.
CD/VCD/MP3-CD Operation
VIDEO CD
1
3
2
4
6
5
7
9
8
VOLUME
0
2
TAPE 1/2
OSD
VCD 123
AUX TUNER
á
à
ë
í
Ç
VAC
DSC
wOOxECHO
RETURN
PBC
DIGEST
É
Å
TITLE
_
TITLE
+
ALBUM
_
ALBUM
+
TITLE/
ALBUM
NAME
A-B
RESUME
ZOOM
SLOW
VOCAL
KEY CONTROL
IS
+-
ON/OFF
LEVEL
MP3 123
Ö
REPEATPROG
Adjusting the TV System
Before viewing the Video CD, ensure that the set
is switched to corresponding PAL or NTSC
system of your TV set (except Multi–system TV).
● Press and hold PAL/NTSC for
more than 2 seconds to
switch between PAL or NTSC
TV system.
➜ After TV system is selected,
the set will automatically switch
to the last TV system setting every time the VCD
source is selected.
Note:
– Before adjusting the TV system, make sure that
there is no MP3-CD in disc tray 1 during power up.
www.freeservicemanuals.info
Published in Heiloo, Holland.
To Next Page
Loading...
