Storing Preset Radio Stations
You can store up to 40 preset radio stations in
the memory.
Automatic Preset Programming
● Plug and Play setting (refer to “Basic Functions -
Plug and Play”).
OR
1
Press TUNER (BAND) to select TUNER mode.
➜ "TUNER" will be displayed. A few seconds
later, the current radio frequency will appear on
the display.
➜ If an FM station is received in stereo,
will
appear on the display.
To begin automatic preset from a desired
preset number
● Press í or ë to select the desired preset
number.
➜ If a radio station has been stored in one of
the presets, it will not be stored again under
another preset number.
2
Press and hold PROG until "AUTO" appears on
the display.
➜
PROG
will start flashing.
➜ The system will start searching for all radio
stations on the FM band, then the MW band.
➜ All available radio stations with strong signal
strength will be stored automatically.
➜ The system will stop searching when all the
available radio stations are stored or when the
memory for 40 preset radio stations is used.
➜ The last preset radio station will then be
played when completed.
To stop storing the automatic preset
● Press PROG or Ç on the system.
Note:
– If no preset number is selected, automatic preset
will begin from preset (1) and all your former
presets will be overridden.
Manual Preset Programming
1
Press TUNER (BAND) repeatedly to select the
desired waveband : FM or MW.
2
Press PROG.
➜
PROG
will start flashing.
➜ The next available preset number will be
displayed for selection.
3
Press and hold à or á until the frequency
indication starts to change, then release.
➜ The display will show "SEARCH" until a radio
station with sufficient signal strength is found.
To store the radio station to another
preset number
● Press í or ë to select the desired preset
number.
4
Press PROG again to store the radio station.
➜
PROG
will disappear from the display.
● Repeat steps 2–4 to store other preset radio
stations.
Tuning to a weak radio station
● Press à or á briefly and repeatedly until the
optimal reception is found.
To stop storing the manual preset
● Press Ç
on the system.
24
English
Notes:
– If you attempt to store more than 40 preset
radio stations, "
PROGRAM FULL
" will be
displayed.
– During programming, if no button is pressed
within 20 seconds, the system will exit the
Programme mode automatically.
Tuning to Preset Radio Stations
● Once you’ve preset the radio stations, press í
or ë to select the desired preset number.
➜ The preset number, radio frequency, and
waveband will appear on the display.
Erasing a Preset Radio Station
1
Press í or ë to select the preset radio station
to be erased.
2
Press and hold Çon the system until “PRESET
DELETED” appears on the display.
➜ The radio frequency remain on the display.
➜ The preset numbers of all other preset radio
stations in the band with higher numbers are also
decreased by one.
● Repeat steps 1–2 to erase other preset radio
stations.
For Recording, please refer to “Tape
Operation/Recording”.
Radio Reception
Changing Tuning Grid
In some countries, the frequency step between
adjacent channels in the MW band is 10 kHz (9
kHz in some areas). The preset frequency step
in the factory is 9 kHz.
Changing the tuning grid will erase all
previously stored preset radio stations.
1
Disconnect the system from the AC power
supply (pull out the AC power cord).
2
While holding down TUNER and á on the
system, reconnect the system to the AC power
supply.
➜ The display will show "GRID 9" or "GRID
10".
Notes:
– GRID 9 and GRID 10 indicate that the tuning
grid is in step of 9 kHz and 10 kHz respectively.
– The FM tuning grid also will be changed from
50 kHz to 100 kHz or vice versa.
To Next Page
Loading...
