Philips FW-V720 - Track and Program Selection

2-12
27
English
Ta pe Operation/Recording
To stop recording
● Press Ç.
➜ Recording and disc playback will stop simultaneously.
Dubbing Tapes
1
Load the prerecorded tape in tape deck 1.
● You can set the tape to the desired passage
where recording will start.
2
Press DUBBING. ➜ Playing and recording will start simultaneously. ➜ "DUB OOO" will be displayed.
● Dubbing of tapes is possible on one side of the
tape only. To continue recording on the reverse side, at the end of side A, flip the tapes to side B and repeat the procedure.
To stop dubbing
● Press Ç.
Notes: – Dubbing of tapes is possible only from tape deck 1 to tape deck 2. –To ensure good dubbing, use tapes of the same length. –You can listen to another source while dubbing.
Microphone Mixing Connect a microphone (not supplied) to the system allowing you to sing along with the music source.
1
Connect a microphone to the MIC jack.
● Before connecting the microphone, set the
microphone LEVEL to the minimum level to prevent howling sound.
2
Press VCD, TUNER, TAPE or AUX to select the source to be mixed and start playback.
Karaoke
MIC/
LEVEL
3
Adjust the volume level of the source with VOLUME control.
4
Adjust the microphone volume with microphone LEVEL control. Note: –Keep the microphone away from the speakers to prevent howling. For Recording, please refer to “Tape Operation/Recording”.
28
English
Clock/Timer
FW-
VCD MI NI HIFI SY STEM
ECO POWER
CD 1•2•3
BAND
CDR/ DVD
TAPE 1•2
PROG
DUBBING REC
CLOCK•
TIMER
AUTO
REPLAY
STANDBY-ON
MUSIC LEVEL
INTERACTIVE VU METER
VOLUME
VOLUME
P
R
E
V
P
R
E
S
E
T
N
E
X
T
DEMO STOP/ CLEAR
PLAY•
PAUSE
S
E
A
R
C
H
•
T
U
N
I
N
G
TUNER
TAPE AUX
DISPLAY
S
O
U
N
D
N
A
V
I
G
ATION - JOG
SOURCE
D
O
LBY
B N
R
S
U
R
R
O
U
N
D
V
A
C
D
S
C
I
N
C
R
E
D
I
B
L
E
VCD
PAL /
NTSC
ON• OFF LEVEL
PBC
RETURN
TITLE/
ALBUM
NAME
T
I
T
L
E
A
L
B
U
M
MIC/
LEVE L
DYNAMIC AMPLI FICATION CONTRO L
1
3
2
4
6
5
7
9
8
VOLUME
0
2
TAPE 1/2
OSD
VCD 123
AUX TUNER
á
à
ë
í
Ç
É
Å
TITLE
_
TITLE
+
ALBUM
_
ALBUM
+
MP3 123
REPEATPROG
MP3
-
CD
View Clock The clock (if it is set) will be shown in Standby mode. To view the clock in any source mode (VCD or TUNER for example)
● Press CLOCK•TIMER.
➜ The clock will be displayed for a few seconds. ➜ If the clock has not been set, "--:--" will be displayed.
Clock Setting The clock can be set in either 12-hour or 24-hour mode ("AM 12:00" or "00:00" for example)
1
Press CLOCK•TIMER twice.
2
Press PROG on the system repeatedly to select clock mode. ➜ If 12-hour mode is selected, "AM 12:00" will start flashing. ➜ If 24-hour mode is selected, "00:00" will start flashing.
3
Press à or á on the system repeatedly to set the hour.
4
Press í or ë on the system repeatedly to set the minute.
5
Press CLOCK•TIMER again to store the setting. ➜ The clock will start working. To exit without storing the setting
● Press Çon the system.
Notes: – The clock setting will be cancelled when the power cord is disconnected or if a power failure occurs. – During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically.
Timer Setting The system can switch on to VCD, TUNER, or TAPE 2 mode automatically at a preset time, serving as an alarm to wake you up. IMPORTANT! – Before setting the timer, ensure that the clock is set correctly. – The timer will always be switched on after it has been set. – The timer will not start if a recording is in progress. – The volume of the timer will increase gradually from the minimum level to the last tuned volume level.
1
Press and hold CLOCK•TIMER for more than two seconds to select timer mode.
➜ "AM 12:00" or "00:00" or the last timer
setting will start flashing.
➜
TIMER
will start flashing.
➜ The selected source will be lighted while
other availab
le sources are flashing.
2
Press VCD, TUNER or TAPE to select the desired source.
www.freeservicemanuals.info
1/3/16
Published in Heiloo, Holland.