29
English
● Before setting the timer, make sure the music
source has been prepared.
VCD – Load the disc(s). To start from a specific
track, make a programme (refer to “CD/VCD/
MP3-CD Operation - Programming the disc
tracks”).
TUNER – tune to the desired radio station.
TAPE – load the prerecorded tape into tape
deck 2.
3
Press à or á on the system repeatedly to set
the hour for the timer to start.
4
Press í or ë on the system repeatedly to set
the minute for the timer to start.
5
Press CLOCK•TIMER to store the start time.
➜ "TIMER ON" will be displayed and followed
by the set timer "XX:XX" and then the selected
source.
➜
TIMER
will remain on the display.
● At the preset time, the selected source will play.
To exit without storing the setting
● Press Çon the system.
Clock/Timer
To deactivate the TIMER
1
Press and hold CLOCK•TIMER for more than
two seconds.
2
Press Çon the system to cancel the timer.
➜ The display will show "CANCEL" and
TIMER
will disappear from the display.
To activate the TIMER (for the same preset
time and source)
1
Press and hold CLOCK•TIMER for more than
two seconds.
2
Press CLOCK•TIMER again to store the start
time.
➜ The last set timer information will be shown
for a few seconds and
TIMER
will appear on
the display.
Notes:
– If the source selected is VCD, playback will begin
with the first track of the last selected disc or other
trays if disc is empty. If all the disc trays are empty,
TUNER will be selected instead.
– During timer setting, if no button is pressed
within 90 seconds, the system will exit timer setting
mode automatically.
Listening to External Sources
1
Connect the audio out terminals of the external
equipment (TV, VCR, Laser Disc player, DVD
player or CD Recorder) to the AUX/CDR IN
terminals of your system.
ECO POWER
CD 1•2•3
BAND
CDR/ DVD
TAPE 1•2
PROG
DUBBING REC
CLOCK•
TIMER
AUTO
REPLAY
STANDBY-ON
MUSIC LEVEL
INTERACTIVE VU MET
P
R
E
V
P
R
E
S
E
T
N
E
X
T
DEMO
STOP/
CLEAR
PLAY•
PAUSE
S
E
A
R
C
H
•
T
U
N
I
N
G
TUNER
TAP E AUX
DISPLAY
SOURCE
D
O
LB
Y
B
N
R
VCD
PAL/
NTSC
ON• OFF LEVE
PBC
R
ETU
RN
TITLE/
ALBUM
NAME
T
I
T
L
E
A
L
B
U
M
MIC/
LEVEL
DYNAMIC AMPLIFICATION CON
MP3
-
CD
External Sources
2
Press AUX (CDR/DVD) repeatedly to select
CDR/DVD mode or normal AUX mode.
➜ "CDR/DVD" or "AUX" will be displayed.
● If the sound from the external source is
distorted, select CDR/DVD mode for listening.
Notes:
–You are advised not to listen to and record from
the same source simultaneously.
– All the navigation sound control features (DSC or
VAC for example) are available for selection.
– Refer to the operating instructions for the
connected equipment for details.
For Recording, please refer to “Tape
Operation/Recording”.
31
English
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the
warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If you
are unable to remedy a problem by following these hints, consult your dealer or service centre.
Problem Solution
DISC PLAYER OPERATION
“UNREADABLE DISC” is displayed. – Check if the disc is inserted upside down.
–Wait until the moisture condensation at the lens
has cleared.
– Replace or clean the disc, see “Maintenance”.
– Use a readable disc or correct recorded format
MP3-CD.
“NO DISC” is displayed. – Insert a disc.
No picture on TV screen. – Connect the cable betwen the system and TV.
No colour on TV. – Change the system to the respective PAL or
NTSC setting.
Cannot adjust the TV system to – Remove the MP-3 CD from disc tray 1 or press
PAL or NTSC. DISC CHANGE to select a non MP3 disc tray
Maintenance
Cleaning the Cabinet
● Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
● When a disc becomes dirty,
clean it with a cleaning cloth.
Wipe the disc from the centre
out. Do not wipe in circular
motion.
● Do not use solvents such as
benzine, thinner, commercially
available cleaners, or antistatic spray intended for
analogue records.
Cleaning the disc lens
● After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
playback quality, clean the disc lens with Philips
CD Lens Cleaner or any commercially available
cleaner. Follow the instructions supplied with
cleaner.
Cleaning the Heads and the Tape Paths
● To ensure good recording and playback quality,
clean the heads
A
, the capstan(s)
B
, and
pressure roller(s)
C
after every 50 hours of
tape operation.
● Use a cotton swab slightly moistened with
cleaning fluid or alcohol.
● You also can clean the heads by playing a
cleaning tape once.
Demagnetising the heads
● Use a demagnetising tape available at your
dealer.
2-13
www.freeservicemanuals.info
Published in Heiloo, Holland.
To Next Page
Loading...
