IMPORTANT!
– Before playing a tape, check and tighten
slack tape with a pencil. Slack tape may get
jammed or may burst in the mechanism.
– C-120 tape is extremely thin and is easily
deformed or damaged. It is not
recommended for use in this system.
– Store the tapes at room temperature and
do not put them too close to a magnetic
field (for example, a transformer, TV or
speaker).
Ta pe Playback
1
Press çto open the tape
deck door.
2
Insert a recorded tape and
close the tape door.
● Load the tape with the open
side down and the full spool
to the left.
3
Press TAPE (TAPE 1•2) repeatedly to select
tape deck 1 or tape deck 2.
➜ The selected tape deck number is displayed.
4
Press PLAYÉÅ to start playback.
To stop playback
● Press Ç.
To change the playback mode
● Press AUTO REPLAY repeatedly to select the
different playback modes.
➜ "AUTO REPLAY" ( å ) or "ONCE" will
appear on the display.
AUTO REPLAY …the tape will rewind
automatically at the end of
playback and replay again. It will
replay up to a maximum of 20
times or until you press Ç.
ONCE .............. the tape will playback the
selected side once and then stop.
To rewind or fast forward during
playback
● Press and hold à or á until the desired
passage is reached, then release.
➜ The tape continues playing.
● The tape will stop automatically at the end of
the tape during rewinding or fast forwarding.
➜ During searching, the sound is reduced to a
low volume.
To rewind or fast forward when playback
is stopped
1
Press à or á.
2
Press Ç when you reached the desired passage.
26
English
To reset tape counter number
● When in stop mode, pressÇ.
➜ “TP1 000” or “TP2 000” will be displayed.
Notes:
– During rewinding or fast forwarding of a tape, it
is also possible to select another source (VCD,
TUNER or AUX, for example).
– The tape counter will automatically set to zero
after detecting end of tape.
General Information on
Recording
● If you do not intend to record via the
microphone, unplug the microphone to avoid
accidental mixing with other recording source.
● For recording, use only tape of IEC type I
(normal tape) or IEC type II (Cr0
2
).
● The recording level is set automatically, regardless
of the position of the Volume, VAC, DSC and so
forth.
● The tape is secured at both ends with leader
tape. At the beginning and end
of the tape, nothing will be
recorded for six to seven
seconds.
● To prevent accidental recording,
break out the tab on the left
shoulder of the tape side you
want to protect.
● If “CHECK TAPE” is displayed, the protection
tab has been broken. Put a piece of clear
adhesive tape over the opening. Do not cover
the Cr0
2
tape detection hole when covering the
tab opening.
IMPORTANT!
– Recording is permissible if copyright or
other rights of third parties are not
infringed upon.
– Recording is possible only on tape deck 2.
Preparation for Recording
1
Press TAPE (TAPE 1•2) to select TAPE 2.
2
Load a recordable tape into tape deck 2 with full
spool to the left.
3
Prepare the source to be recorded.
VCD – load the disc(s).
TUNER – tune to the desired radio station.
TAPE – load the prerecorded tape into tape
deck 1 with the full spool to the left.
AUX – connect external equipment.
When recording is in progress
➜
starts flashing.
● It is not possible to listen to another sources
except when dubbing tapes.
● It is not possible to activate the timer function.
One Touch Recording/Recording
the mixed sound
1
Press VCD, TUNER or AUX to select the
source.
● You can connect a microphone to record the
mixed sound in tape deck 2 (refer to “Karaoke -
Microphone Mixing”).
2
Start playback of the selected source.
3
Press REC to start recording.
To stop recording
● Press Ç on the system.
Note:
– One Touch Recording is not possible in TAPE
mode, "
SELECT SOURCE
" will be displayed.
CD/VCD/MP3-CD Synchro
Recording
1
Press VCD to select the disc.
● Press í or ë to select the desired track to
start recording.
● You can programme the tracks in the order you
want them to be recorded (refer to “CD/VCD/
MP3-CD Operation - Programming the disc
tracks”).
2
Press REC to start recording.
➜ The disc will start playback automatically.
To select another track during recording
1
Press PAUSEÉÅ to interrupt recording.
2
Pressí or ë to select the desired track.
3
Press PLAYÉÅ to resume recording.
Ta pe Operation/Recording
To Next Page
Loading...
