Pioneer PDP-427XD - DISASSEMBLY; SERVICE FACTORY MODE

PDP-427XD
9
5678
56
7
8
C
D
F
A
B
E
6.2 DISASSEMBLY..................................................................................................................................................101
7. ADJUSTMENT .........................................................................................................................................................107
7.1 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED.................................................107
7.2 ADJUSTMENT REQUIRED WHEN PART IS REPLACED ................................................................................108
7.3 BACKUP WHEN THE PANEL UNIT IS ADJUSTED..........................................................................................109
7.4 HOW TO CLEAR HISTORY DATA .....................................................................................................................112
7.5 ADJUSTMENT WHEN THE SERVICE PANEL ASSY IS REPLACED ..............................................................113
8. SERVICE FACTORY MODE ....................................................................................................................................115
8.1 OUTLINE OF THE SERVICE FACTORY ...........................................................................................................115
8.1.1 SERVICE FACTORY MODE TRANSITION CHART....................................................................................115
8.1.2 HOW TO ENTER/EXIT SERVICE FACTORY MODE..................................................................................115
8.1.3 OPERATION OF SERVICE FACTORY MODE............................................................................................115
8.1.4 REMOTE COTROL CODE..........................................................................................................................116
8.1.5 FACTORY HIERARCHICAL TABLE ............................................................................................................117
8.1.6 INDICATIONS IN SERVICE FACTORY MODE ...........................................................................................118
8.2 FACTORY MENU...............................................................................................................................................120
8.2.1 INFORMATION............................................................................................................................................120
8.2.2 PANEL FACTORY .......................................................................................................................................128
8.2.3 OPTION.......................................................................................................................................................138
8.2.4 INITIALIZE...................................................................................................................................................138
9. RS-232C ..................................................................................................................................................................141
9.1 OUTLINE OF RS-232C COMMAND .................................................................................................................141
9.1.1 PREPARED TOOLS ....................................................................................................................................141
9.1.2 USING RS-232C COMMANDS...................................................................................................................141
9.1.3 COMMAND PROTOCOL.............................................................................................................................142
9.1.4 COMMAND DEFINITION............................................................................................................................143
9.2 LIST OF RS-232C COMMANDS.......................................................................................................................145
9.3 OUTLINE OF EACH COMMANDS....................................................................................................................151
9.3.1 ACQUISITION OF PANEL STATUS • • • [QS1] ...........................................................................................151
9.3.2 ACQUISITION OF PANEL OPERATION DATA • • • [QS2] ..........................................................................152
9.3.3 ACQUISITION OF OTHER DATA ON THE PANEL • • • [QIP] .....................................................................153
9.3.4 ACQUISITION OF PANEL ADJUSTMENT DATA (COMMON DATA) • • • [QAJ] .........................................153
9.3.5 ACQUISITION OF ABL/WB ADJUSTMENT DATA • • • [QPW] ...................................................................154
9.3.6 ACQUISITION OF PULSE METER VALUE • • • [QPM] ..............................................................................154
9.3.7 ACQUISITION OF PD LOGS • • • [QPD].....................................................................................................155
9.3.8 ACQUISITION OF SD LOGS • • • [QSD].....................................................................................................156
9.3.9 QS6 .............................................................................................................................................................157
9.3.10 QMT ..........................................................................................................................................................157
9.3.11 QNG ..........................................................................................................................................................158
9.3.12 DRV...........................................................................................................................................................159
9.3.13 OTHER COMMANDS ...............................................................................................................................160
10. GENERAL INFORMATION ....................................................................................................................................161
10.1 POWER ON SEQUENCE................................................................................................................................161
10.2 POWER SUPPLY TRANSITION STATUS........................................................................................................164
10.3 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM .............................................................165
10.4 LED INFORMATION........................................................................................................................................166
10.5 SPECIFICATION ABOUT THE THERMAL PROTECTION..............................................................................167
10.6 PROCESSING IN ABNORMALITY .................................................................................................................168
11. SPECIFICATIONS..................................................................................................................................................170
11.1 SPECIFICATIONS ...........................................................................................................................................170
11.2 ACCESSORIES...............................................................................................................................................171
11.3 PANEL FACILITIES..........................................................................................................................................172
11.3.1 PDP-427XD, PDP-4270XD .......................................................................................................................172
11.3.2 PDP-427XA, PDP-4270XA........................................................................................................................177
12. IC INFORMATION ..................................................................................................................................................182