Pit Boss 10923 - User Manual

Questions and Answers

R
Rebecca AdamsAug 20, 2025
How to fix Err error code with igniter icon blinking on Pit Boss 10923 Grill?
- A
  Amy RodriguezAug 20, 2025
  If you see an Err error code with the igniter icon blinking on your Pit Boss Grill, this indicates the igniter isn't working properly or isn't making a connection. Inspect the igniter by removing cooking components, turning on the unit, and feeling for heat above the burn grate. Also, confirm the igniter is aligned with the hole in the burn grate and open to light the pellets. The igniter may need to be replaced.
B
Bradley BryanAug 22, 2025
Why are there no power lights on my Pit Boss Grill control board?
- S
  Sherry WilliamsAug 22, 2025
  If there are no power lights on the control board of your Pit Boss Grill, several issues could be the cause. First, ensure the unit is properly plugged into a working power source and try resetting the breaker. Also, confirm that the GFCI is a minimum 15 Amp service. Check that all wire connections are firmly connected and dry. Another possibility is a blown fuse on the control board, which would need to be manually replaced after inspecting it for a broken or blackened wire. The GFCI outlet may have been tripped. In rare cases, the control board itself might be faulty and require replacement.
C
Cindy MillerAug 25, 2025
Why won't my Pit Boss 10923 Grill maintain a stable temperature?
- W
  weissjoyAug 25, 2025
  If your Pit Boss Grill isn't maintaining a stable temperature, start by checking the burn pot for ash build-up or any obstructions, and ensure the fan is working correctly with no blockage of air intake. Also, check the auger motor to confirm it's operating properly and that there isn't any blockage in the auger tube. Make sure the fuel level is sufficient and of good quality, without overly long pellets that could cause obstructions. Check the status of the grill probe; clean it if dirty. After completing these steps, start the grill at COOK temperature to SMOKE and wait for 10 minutes, ensuring the flame is bright and vibrant.
K
Kathleen HallAug 26, 2025
What to do if the fire in burn pot will not light in Pit Boss Grill?
- Z
  Zachary ThompsonAug 26, 2025
  If the fire in the burn pot of your Pit Boss Grill won't light, it might be because the auger isn't primed, preventing pellets from reaching the burn pot. In this case, you should follow the Auger Priming Procedure. Another potential cause is a jammed auger motor. To check this, remove the cooking components and inspect the auger feed system to see if pellets are dropping into the burn pot. You can also inspect the igniter by ensuring it is protruding approximately 13mm / 0.5 inches into the burn pot and feeling for heat when the unit is turned on.
L
Laura FullerAug 27, 2025
How to fix Err error code with AUGER icon blinking on Pit Boss 10923 Grill?
- T
  Tina HicksAug 27, 2025
  An Err error code with the AUGER icon blinking on your Pit Boss Grill typically means the auger is not primed or the auger motor is jammed. Ensure the auger is primed, especially if the unit is new or the hopper was emptied. Follow the Auger Priming Procedure. Also, check if the auger motor is jammed by removing cooking components and inspecting the auger feed system to confirm pellets are dropping into the burn pot.
S
Steve WardAug 29, 2025
Why does my Pit Boss 10923 Grill produce excessive or discolored smoke?
- J
  Jennifer StevensAug 29, 2025
  Excessive or discolored smoke from your Pit Boss Grill can be due to several factors. It could be caused by grease build-up, so follow the Care and Maintenance instructions. Poor hardwood pellet quality, such as moist pellets, can also be a culprit; remove them from the hopper and replace them with dry pellets. A blocked burn pot or insufficient air intake for the fan could also be responsible; ensure the fan is working properly and the air intake is not blocked.
N
ncastanedaAug 31, 2025
How to fix Err error code with FAN icon blinking on Pit Boss 10923 Grill?
- D
  daniellepowersAug 31, 2025
  An Err error code with the FAN icon blinking on your Pit Boss Grill suggests the fan isn't working properly or making a connection. Check the fan to ensure it is working correctly and that the air intake is not blocked. Inspect the fan wires for any damage. If the fan blades are dirty, follow the Care and Maintenance instructions.
T
Tina BrooksSep 2, 2025
What to do if the temperature readout won't adjust on Pit Boss 10923 Grill?
- A
  Audrey FoxSep 2, 2025
  If the temperature readout on your Pit Boss Grill isn't adjusting, the grill probe might be dirty or broken. You can start by following the Care and Maintenance instructions to clean the probe.
N
natasha39Sep 4, 2025
How to prevent frequent flare-ups on Pit Boss 10923?
- M
  Mrs. Elizabeth ThomasSep 4, 2025
  To prevent frequent flare-ups on your Pit Boss Grill, try cooking at a lower temperature, especially when cooking highly greasy food, keeping it under 176°C / 350°F. Also, ensure that grease build-up on cooking components is minimized by following the Care and Maintenance instructions.
A
Amy CainSep 6, 2025
How to fix Err error code with PELLET icon blinking on Pit Boss 10923?
- J
  Jacqueline SnyderSep 6, 2025
  An Err error code with the PELLET icon blinking on your Pit Boss Grill indicates a lack of fuel, poor fuel quality, an obstruction in the feed system, or a jammed auger. Check the hopper to ensure the fuel level is sufficient and replenish if low. If the hardwood pellets are of poor quality or too long, remove them and follow Care and Maintenance instructions.