Pit Boss PB1600PS1 - User Manual

Questions and Answers

D
Dustin MillerAug 18, 2025
Why won't the fire pot light in my Pit Boss PB1600PS1 Grill?
- M
  Michael ThomasAug 18, 2025
  If the fire in your Pit Boss Grill fire pot won't light, it could be due to several reasons. First, if the unit is being used for the first time or the hopper was completely emptied, the auger may not be primed, preventing pellets from reaching the fire pot. Follow the Hopper Priming Procedure. Alternatively, the auger motor may be jammed; remove cooking components and inspect the auger feed system to ensure pellets are dropping into the fire pot. If not, contact Customer Service. Lastly, the ignitor may have failed; remove cooking components, turn the unit on, and check if the ignitor is heating up by placing your hand above the fire pot. Also, confirm that the ignitor is protruding approximately 13mm / 0.5 inches into the fire pot.
E
erinmorseAug 20, 2025
How to fix Pit Boss PB1600PS1 Grill not maintaining temperature?
- J
  Jerome CalderonAug 20, 2025
  If your Pit Boss Grill isn't reaching or maintaining a stable temperature, start by checking the fire pot for ash build-up or obstructions and ensure sufficient airflow. Make sure the fan is working properly and the air intake is not blocked. Also, inspect the auger motor to confirm operation and ensure there's no blockage in the auger tube. Next, verify that the fuel level in the hopper is sufficient and that the wood pellets are of good quality and not too long, which could cause an obstruction in the feed system. Finally, check the status of the grill probe; a dirty or damaged probe can affect temperature readings.
K
Kelsey GillespieAug 23, 2025
Why is my Pit Boss PB1600PS1 producing too much smoke?
- S
  Sharon PowellAug 23, 2025
  Excessive or discolored smoke from your Pit Boss Grill can be caused by several factors. Check for grease build-up and follow the care and maintenance instructions to resolve this. The quality of the wood pellets may also be a factor; remove any moist pellets and replace them with dry ones. Additionally, ensure the fire pot is not blocked and follow the Hopper Priming Procedure. Finally, check the fan to ensure it's working properly and the air intake is not blocked.
M
mhawkinsAug 26, 2025
What to do if my Pit Boss PB1600PS1 Grill shows Err error code with IGNITOR error?
- M
  Madeline SandersAug 26, 2025
  If your Pit Boss Grill displays an Err error code with the IGNITOR error code blinking, it indicates that the ignitor is not working properly or is not making a connection. To resolve this, remove the cooking components and inspect the igniter. Visually confirm that the igniter is working by placing your hand above the burn grate and feeling for heat. Also, check that the igniter is aligned with the hole in the burn grate, allowing it to light the pellets. If it's still not working, the igniter may need to be replaced.
M
maddenmichaelAug 27, 2025
What does Err error code with PELLET mean on Pit Boss PB1600PS1 Grill?
- M
  Melinda AdamsAug 27, 2025
  If your Pit Boss Grill displays an Err error code with the PELLET error code blinking, it typically indicates a lack of fuel, poor fuel quality, an obstruction in the feed system, or a jammed auger. Check the hopper to ensure the fuel level is sufficient and replenish if low. If the wood pellets are of poor quality or too long, remove them and follow the care and maintenance instructions to clean out any obstructions.
J
Jamie HornAug 30, 2025
What does Err error code with AUGER mean on Pit Boss Grill?
- K
  Kathy GarzaAug 30, 2025
  If your Pit Boss Grill shows an Err error code with the AUGER error code blinking, this may be because the auger isn't primed. Before using the unit for the first time, or after completely emptying the hopper, the auger must be primed to allow pellets to fill the feed system. Follow the Hopper Priming Procedure. Another potential cause is a jammed auger motor or a connection issue. Remove the cooking components, turn the unit on, and inspect the auger feed system to ensure pellets are dropping into the burn pot.
K
Kyle WilliamsSep 1, 2025
What does Err error code with FAN mean on Pit Boss PB1600PS1?
- K
  Karen MartinSep 1, 2025
  If your Pit Boss Grill displays an Err error code with the FAN error code blinking, it means the fan is not working properly or is not making a connection. Check the fan to ensure it is working and that the air intake is not blocked. Also, check for any damage to the fan wires. If the fan blades are dirty, follow the care and maintenance instructions to clean them.
S
Stephanie DeckerSep 3, 2025
Why won't the temperature adjust on my Pit Boss PB1600PS1?
- H
  hjamesSep 3, 2025
  If the temperature readout on your Pit Boss Grill isn't adjusting, the grill probe may be dirty. Follow the care and maintenance instructions to clean it. If cleaning doesn't resolve the issue, the grill probe may be broken and needs to be replaced.
M
Mr. Sean MooreSep 6, 2025
Why are there no power lights on my Pit Boss PB1600PS1 control board?
- H
  hparkerSep 6, 2025
  If there are no power lights on the control board of your Pit Boss Grill, first ensure the unit is plugged into a working power source and reset the breaker. Confirm the GFCI is a minimum 10 Amp service. Check that all wire connections are firmly connected and dry. If the issue persists, the fuse on the control board may be blown. To check, remove the hopper access panel and carefully pull the controller inside the hopper to release it. Examine the fuse for a broken or blackened wire, and replace it if necessary. A faulty control board may also be the reason, in that case, the control board needs to be replaced.
A
Angela GonzalezSep 8, 2025
How to stop flare-ups on my Pit Boss PB1600PS1?
- J
  Johnathan SantosSep 8, 2025
  Frequent flare-ups in your Pit Boss Grill can often be attributed to the cooking temperature being too high, especially when cooking greasy foods. Try cooking at a lower temperature, ideally below 176°C / 350°F. Another cause could be grease build-up on the cooking components. Follow the care and maintenance instructions to clean them thoroughly.