Pit Boss PB1100PS1 User Manual (English)

Questions and Answers:

D
dakota48Aug 18, 2025
What to do if my Pit Boss PB1100PS1 Grill shows an "ErH" error code?
- R
  Rodney DiazAug 18, 2025
  If the Pit Boss Grill unit has overheated, possibly due to a grease fire or excess fuel, press the Power Button to turn the unit off, and allow the grill to cool. After it cools, remove the pellets and confirm the positioning of all component parts. Once cooled, press the Power Button to turn the unit on, then select the desired temperature. If the error code is still displayed, contact Customer Service.
K
Kaylee ReynoldsAug 20, 2025
How to fix a Pit Boss PB1100PS1 if the fire pot will not light?
- T
  Tony DickersonAug 20, 2025
  If the fire pot of your Pit Boss Grill will not light, it could be due to several reasons. First, if the auger is not primed, follow the Hopper Priming Procedure. If the auger motor is jammed, remove cooking components, turn the Temperature Control Dial to SMOKE, and inspect the auger feed system. Visually confirm that the auger is dropping pellets into the fire pot. Also, inspect the igniter to confirm it is working, by placing your hand above the fire pot and feeling for heat and visually confirm that the igniter is protruding approximately 13mm / 0.5 inches in the fire pot.
M
Mathew FloresAug 23, 2025
Why won't my Pit Boss PB1100PS1 achieve or maintain a stable temperature?
- D
  Denise BaileyAug 23, 2025
  If your Pit Boss Grill is not achieving or maintaining a stable temperature, check the fire pot for ash build-up or obstructions. Also, check the fan to ensure it is working properly and the air intake is not blocked. Confirm the auger motor is operating and there is no blockage in the auger tube. Ensure the fuel level is sufficient and of good quality, without obstructions in the feed system. Check the status of the temperature probe.
K
Kenneth McculloughAug 26, 2025
Why does my Pit Boss PB1100PS1 produce excess or discolored smoke?
- T
  Tracy SextonAug 26, 2025
  If your Pit Boss Grill produces excess or discolored smoke, it may be due to grease build-up, so follow the Care and Maintenance instructions. Also, check the wood pellet quality and replace moist pellets with dry ones. Ensure the fire pot is not blocked and there is sufficient air intake for the fan.
J
Joseph HuynhAug 28, 2025
How to lower the temperature on SMOKE setting on my Pit Boss Grill?
- A
  Andrea RodriguezAug 28, 2025
  If the Pit Boss Grill temperature on SMOKE is too high, push the "P" SET button, and increase the "P" setting.
A
Andre PowellAug 30, 2025
What does the "Err" error code mean on my Pit Boss Grill?
- T
  tammymayerAug 31, 2025
  If the Pit Boss Grill shows an "Err" error code, remove the hopper access panel and check for any damage to the Temperature Probe wires. Ensure the Temperature Probe molex connectors are firmly connected, and connected correctly, to the Control Board.
C
cochoaSep 2, 2025
What does the "ErP" error code mean on my Pit Boss PB1100PS1 Grill?
- A
  Amanda CabreraSep 2, 2025
  If the Pit Boss Grill displays an "ErP" error code, press the Power Button to turn the unit off, wait two minutes, then press the Power Button to turn the unit on again. Turn the Temperature Control Dial to SMOKE or the desired temperature. This safety feature prevents an automatic restart if the unit was not turned off properly when last connected to power.
T
timothygarciaSep 4, 2025
What does the "noP" error code mean on my Pit Boss PB1100PS1?
- A
  Anne TurnerSep 4, 2025
  If the Pit Boss Grill displays a "noP" error code, disconnect the meat probe from the connection port on the Control Board, and reconnect it. Ensure the meat probe adapter is firmly connected and check for signs of damage to the adapter end or the wires of the meat probe. A faulty control board may also be the cause.
J
John BeckSep 7, 2025
Why are there no power lights on my Pit Boss Grill control board?
- E
  Elizabeth CampbellSep 7, 2025
  If there are no power lights on the Pit Boss Grill control board, first, press the Power Button and ensure it glows blue. Then, turn the Temperature Control Dial to a temperature setting. Also, ensure the unit is plugged into a working power source and reset the breaker. Check that the GFCI is a minimum 10 Amp service and all wire connections are firmly connected and dry. If the issue persists, the fuse on the control board may be blown and needs replacing, or the control board may be faulty and needs to be replaced.
M
Monique BarkerSep 9, 2025
What do flashing dots on the LCD screen of my Pit Boss PB1100PS1 Grill mean?
- J
  Jeffrey SmithSep 10, 2025
  If you see flashing dots on the LCD screen of your Pit Boss Grill, this indicates the unit has power and is in Start-Up mode with the igniter on. This is normal and not an error. The igniter will turn off after five minutes, and the grill will begin to adjust to the desired temperature once the flashing dots disappear.