Pit Boss TAILGATER - User Manual

Questions and Answers

L
Lee GambleAug 19, 2025
Why won't my Pit Boss TAILGATER maintain a stable temperature?
- B
  Brooke ClarkAug 20, 2025
  If your Pit Boss Grill isn't maintaining a stable temperature, consider these potential causes. Check for sufficient airflow through the fire pot by inspecting for ash build-up or obstructions, ensure the fan is working, and the air intake isn't blocked. Also, verify that the auger motor is operating and there's no blockage in the auger tube. Insufficient or poor-quality fuel, or an obstruction in the feed system, can also be to blame; check the fuel level and quality, and remove any obstructions. Lastly, inspect the temperature probe for dirt.
S
Shawna HayesAug 22, 2025
Why is my Pit Boss TAILGATER producing excess or discolored smoke?
- B
  Brianna LewisAug 23, 2025
  Excess or discolored smoke from your Pit Boss Grill can stem from several issues. Grease build-up is a common cause. Also, the quality of the wood pellets can be a factor; remove any moist pellets and replace them with dry ones. Check for a blocked fire pot and clear any ash or debris. Finally, ensure the fan has sufficient air intake and is free from blockages.
D
Dawn WrightAug 25, 2025
What to do if Pit Boss TAILGATER Grill temperature on SMOKE is too high?
- W
  William BurgessAug 26, 2025
  If the grill temperature on SMOKE setting is too high on your Pit Boss Grill, the "P" setting might be too low. Push the "P" SET button, and increase the "P" setting.
H
hestradaAug 28, 2025
Why is there no power to my Pit Boss TAILGATER Grill control board?
- T
  thomashendrixAug 28, 2025
  If there are no power lights on the control board of your Pit Boss Grill, several factors could be the cause. First, ensure the Temperature Control Dial is not still off, press the Power Button to confirm it glows blue, indicating a power connection, and then turn the Temperature Control Dial to a temperature setting. Check that the unit is properly plugged into a working power source and reset the breaker. Also, the GFCI should be a minimum 10 Amp service. Confirm that all wire connections are firmly connected and dry. Lastly, the fuse on the control board may be blown and needs replacing, or the control board itself may be faulty.
S
Stephanie WrightAug 30, 2025
What to do if the temperature is flashing on my Pit Boss TAILGATER LCD screen?
- A
  Andrea HoustonAug 31, 2025
  A flashing temperature on the LCD screen of your Pit Boss Grill indicates that the grill temperature is below 65°C / 150°F. This is used to show that there is some risk that the fire could go out. Check the hopper for sufficient fuel or if there is an obstruction in the feed system. Remove pellets. Check the grill temperature probe. Check the fire pot for ash build-up or obstructions. Check the fan and auger motor.
A
Alicia FryeSep 2, 2025
How to prevent frequent flare-ups on my Pit Boss TAILGATER?
- T
  Tracy StewartSep 2, 2025
  Frequent flare-ups on your Pit Boss Grill can often be attributed to the cooking temperature being too high, especially when cooking greasy foods, so try cooking at a lower temperature, ideally below 176°C / 350°F. Another cause is grease build-up on the cooking components.
J
Joseph GonzalezSep 5, 2025
What does the "noP" error code mean on my Pit Boss TAILGATER Grill?
- J
  Jessica DonovanSep 5, 2025
  The "noP" error code on your Pit Boss Grill indicates a problem with the meat probe. This could be due to a bad connection at the connection port, so disconnect and reconnect the meat probe from the port on the Control Board, ensuring it's firmly connected and checking for damage to the adapter end. The meat probe itself might be damaged, so inspect the wires for any signs of damage. In some cases, a faulty control board can also trigger this error.
L
Lee ArmstrongSep 8, 2025
What does the "ErH" error code mean on my Pit Boss Grill?
- A
  aaronlaneSep 8, 2025
  The "ErH" error code on your Pit Boss Grill indicates that the unit has overheated, possibly due to a grease fire or excess fuel. Turn the unit off and allow it to cool. After it cools, remove the pellets and confirm the positioning of all component parts. Once cooled, turn the unit back on and select the desired temperature.
C
Christian ThompsonSep 12, 2025
What does "ErP" error code mean on Pit Boss TAILGATER?
- R
  rachelhendrixSep 12, 2025
  The "ErP" error code on your Pit Boss Grill indicates that the unit was not turned off properly when last connected to power. Press the Power Button to turn the unit off, wait two minutes, then press the Power Button to turn the unit on again. Turn Temperature Control Dial to SMOKE or desired temperature.
F
fchanSep 13, 2025
What does "Err" error code mean on Pit Boss Grill?
- D
  Danielle DrakeSep 13, 2025
  The "Err" error code on your Pit Boss Grill indicates that the temperature probe wire is not making a connection. Check for any damage to the Temperature Probe wires. Ensure Temperature Probe molex connectors are firmly connected, and connected correctly, to the Control Board.