EasyManua.ls Logo

Polaris p825 - User Manual

Polaris p825
24 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Diagnostic Test Kit
H0510700 Rev A
WARNING
The Diagnostic Box and included test cables are to be used solely for diagnosing Polaris Robotic Cleaners.
It must not be used for any other purpose. Diagnostic
tests must be performed while the unit is out of the water.
Failure to comply with the following warnings can result in property damage, personal injury, or death.
FOR YOUR SAFETY - This product must be serviced by a contractor who is licensed and qualied in pool equipment by the
jurisdiction in which the product will be installed where such state or local requirements exists. In the event no such state
or local requirement exists, the installer or maintainer must be a professional with sufcient experience in pool equipment
installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this
product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices
and instructions may result in property damage, personal injury, or death. Improper installation and/or operation will void the
warranty.
Improper installation and/or operation can create unwanted electrical hazard which can cause serious injury, property damage,
or death.
Only connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle should be
provided by a qualied installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI
should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is
defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is owing, indicating
the possibility of an electric shock. Do not use this product. Disconnect the cleaner and have the problem corrected by a
qualied service representative before using.
KEEP OUT OF REACH OF CHILDREN
for Polaris Robotic Cleaners
93 94 95 Series
P825
91 Series

Other manuals for Polaris p825

Questions and Answers

  • H
    hrivasJul 26, 2025
    What to do if my Polaris p825 Swimming Pool Vacuum does not stay firmly on the pool bottom?
    • A
      Ashley PerezJul 26, 2025
      If your Polaris Swimming Pool Vacuum isn't staying firmly on the pool bottom, there might be a few reasons. First, check for air trapped in the appliance casing and re-submerge the cleaner. Also, a full or dirty filter canister can cause this issue, so clean it. If neither of those solves the problem, the impeller might be damaged, and you should contact Polaris Technical Support for assistance.
  • M
    Matthew CobbJul 31, 2025
    Why is my Polaris p825 Swimming Pool Vacuum not cleaning effectively?
    • D
      devinsmithJul 31, 2025
      If your Polaris Swimming Pool Vacuum is not cleaning effectively, the brushes may be worn and need replacement. Another cause could be a full or dirty filter canister, so cleaning it is a good first step. Also, if the floating cable is excessively coiled or kinked, spread it out over the pool, ensure it's not tightly wrapped during storage, or lay it straight in the sun to relax it.
  • S
    Sandra WilliamsAug 4, 2025
    How to fix a Polaris p825 that does not climb the pool walls?
    • S
      Shannon ButlerAug 4, 2025
      If your Polaris Swimming Pool Vacuum isn't climbing walls or reaching the waterline, start by cleaning the filter canister, as a full or dirty canister can cause this. Also, if the pool walls are slippery, adjust the Surface Control System™ setting and consider a shock chlorination treatment to reduce pH levels, but remember to remove the cleaner from the pool during this treatment.
  • Q
    qhobbsAug 9, 2025
    Why does my Polaris Swimming Pool Vacuum not move on startup?
    • T
      Tracy CarsonAug 9, 2025
      If your Polaris Swimming Pool Vacuum doesn't move on startup, first check that the outlet the control unit is connected to is receiving electricity. If there's power, the cleaner might have shut down with an error code or flashing lights. Disconnect the control unit, wait at least 20 seconds, and then reconnect it. If the problem continues, contact Polaris Technical Support.
  • N
    Nathan GibsonAug 12, 2025
    What to do if the Cleaner Error Indicator flashes just after starting Polaris p825?
    • S
      susanlongAug 13, 2025
      If the Cleaner Error Indicator flashes just after starting your Polaris Swimming Pool Vacuum, try these steps: Ensure the floating cable is securely plugged into the control unit by unplugging and reconnecting it. Make sure the cleaner is fully submerged in the pool. You might also need to reset the cleaner by turning it off and then pressing the Floor/Wall setting button to begin a new cycle. If the propeller or tracks seem jammed, contact Polaris Technical Support.
  • A
    Adam SmithAug 16, 2025
    What to do if the Cleaner Error Indicator flashes during the cleaning cycle of my Polaris p825 Swimming Pool Vacuum?
    • C
      Craig StricklandAug 17, 2025
      If the Cleaner Error Indicator flashes during the cleaning cycle of your Polaris Swimming Pool Vacuum, it might be sucking in air. Remove the cleaner from the pool and re-submerge it to resolve this issue.
  • D
    David MorrisAug 21, 2025
    How to stop Polaris p825 cable from tangling?
    • A
      April DavisAug 21, 2025
      If the cable is tangling in your pool while using the Polaris Swimming Pool Vacuum, it might be due to too much cable length in the water. Use only the necessary amount for the cleaner to cover the pool area and place the remaining cable on the side of the pool. Follow the Cord Tangling procedure to avoid and correct tangled cords.

Summary

Test for 93, 94, 95 Series Cleaners

93-95 Series Control Box Test Flowchart

Flowchart for diagnosing issues with the 93-95 Series control box.

93-95 Series Cleaner Test Flowchart

Flowchart for diagnosing issues with the 93-95 Series cleaner.

93-95 Series Motor Block Test Flowchart

Flowchart for diagnosing issues with the 93-95 Series motor block.

Test for P825 Cleaner

P825 Control Box Test Flowchart

Flowchart for diagnosing issues with the P825 control box.

P825 Cleaner Test Flowchart

Flowchart for diagnosing issues with the P825 cleaner.

P825 Motor Block Test Flowchart

Flowchart for diagnosing issues with the P825 motor block.

Polaris p825 Specifications

General IconGeneral
Pool TypeIn-ground
Drive4-wheel drive
ScrubbingYes
TypeRobotic Pool Cleaner
Cable Length60 feet
Debris TypeLarge
Power SourceElectric
Cleaning CoverageFloor, Walls, Waterline
Warranty2 years

Related product manuals