Powermatic PM2014 - User Manual

Questions and Answers

R
Robert HardinAug 15, 2025
What causes the headstock to move when applying pressure with the tailstock on my Powermatic PM2014 Lathe?
- J
  Jared McneilAug 15, 2025
  If the headstock moves when applying pressure with the tailstock on your Powermatic Lathe, it could be because the headstock is not locked to the bed, so tighten the headstock locking handle. Another reason might be excessive pressure being applied by the tailstock (more than 500 lbs. of force). Slide the headstock to the left end, then apply pressure to the workpiece with the tailstock. Apply only sufficient force with the tailstock to hold the workpiece securely in place.
J
julie49Aug 18, 2025
Why does the tailstock move when applying pressure on my Powermatic Lathe?
- R
  Randy HowardAug 18, 2025
  If the tailstock moves when applying pressure on your Powermatic Lathe, it could be because the locking handle is not tightened, so tighten the locking handle. Alternatively, the cam lock nut might need adjusting, so turn the tailstock over and tighten the cam lock nut. Another possibility is that the lathe bed and tailstock mating surfaces are greasy or oily, so remove the tailstock and clean the surfaces with a cleaner/degreaser. Re-apply a light coat of oil to the bed surface.
A
Arthur RayAug 22, 2025
Why does my Powermatic Lathe motor fail to develop full power?
- X
  xschmidtAug 22, 2025
  The Powermatic Lathe motor might not develop full power due to several reasons. The power supply line could be overloaded, so correct the overload condition. Alternatively, the wires in the power supply system might be undersized, in which case you should increase the supply wire size. If the display reads “Err”, it indicates an inverter fault, and you should contact Powermatic Technical Service at 800-274-6846. Finally, there could be a motor fault, requiring you to have the motor inspected and replaced.
N
Nicholas HarrisonAug 26, 2025
What to do if my Powermatic Lathe motor or spindle stalls or will not start?
- H
  Heather PhillipsAug 26, 2025
  If your Powermatic Lathe motor or spindle stalls or won't start, there are a few potential causes. You might be taking an excessive cut, so try reducing the depth of cut. The belt might be improperly adjusted, worn, or broken, so adjust or replace the belt as needed. Improper cooling of the motor could also be the issue; blow out sawdust from the motor housing fan. Worn spindle bearings could be the problem, so replace the bearings. Finally, there could be a motor fault, in which case you should have the motor inspected and replaced.
E
Elizabeth HendersonAug 28, 2025
How to fix excessive vibration in my Powermatic Lathe?
- J
  Joseph GibsonAug 28, 2025
  Excessive vibration in your Powermatic Lathe can stem from several issues. The workpiece might be warped, out of round, have a major flaw, or was improperly prepared for turning; correct this by planing or sawing the workpiece, or discard it and use a new one. The motor mount lock handle might be loose, so tighten the lock handle. If the lathe is on an uneven surface, mount it to a level, flat surface and adjust the levelers if using a stand. Worn spindle bearings can also cause vibration, so replace the bearings. Lastly, check for improper belt adjustment or a worn belt and adjust or replace the belt.
L
Luis DavisAug 31, 2025
Why does my Powermatic PM2014 run at one speed only?
- W
  Wanda ParkSep 1, 2025
  Your Powermatic Lathe might be running at only one speed due to a potentiometer (speed dial) fault, in which case you should replace the potentiometer. Alternatively, the electronic AC inverter might not be programmed properly, be defective, or have loose wiring. Contact Powermatic Technical Service at 800-274-6846 to help identify the problem.
K
kbutlerSep 4, 2025
What to do if tools tend to grab or dig in on my Powermatic PM2014?
- R
  Robert HamiltonSep 4, 2025
  If tools tend to grab or dig in on your Powermatic Lathe, it could be due to several reasons. The tools might be dull, so keep them sharp. The tool support might be set too low, so reposition the tool support height. It could also be set too far from the workpiece, so reposition the tool support closer to the workpiece. Finally, you might be using the wrong tool, so use the correct tool for the operation.
R
Robert ClarkSep 7, 2025
What to do if the LED display does not work on my Powermatic PM2014 Lathe?
- S
  Sonya MckinneySep 7, 2025
  If the LED display does not work on your Powermatic Lathe, it could be because the digital sensor is out of position or damaged. Open the belt access door and inspect the sensor. Reposition or replace it.
K
Keith MillerSep 12, 2025
Why does the spindle have a slight wobble (runout) on my Powermatic PM2014 Lathe?
- E
  Elizabeth PhillipsSep 12, 2025
  If the spindle has a slight wobble (runout) on your Powermatic Lathe, it could be due to worn or damaged bearings, in which case you should replace the bearings. It could also be that the spindle is damaged, so replace the spindle.