w ww.practixx .com
34
|
GB
9.2.1 Changing the PIN code (Fig. 22)
• Press and hold the “START” and “HOME” buttons
simultaneously for at least 3 seconds.
• The -symbol and “PIN” ash.
• Now enter the old PIN code as follows (factory set-
ting “0000”).
• The rst digit illuminates (“0---”).
• Use the “START” and “HOME” buttons to select the
desired digit.
• Conrm the digit with the “OK” button.
• The next digit illuminates (e.g. “10--).
• Proceed as described in paragraph 2-4 above.
• After you have entered the “old” PIN code and con-
rmed the fourth digit with the “OK” button, “PIn2”
appears, now you can enter the new PIN code.
• The rst digit ashes (“0---”).
• Use the “START” and “HOME” buttons to select the
desired digit.
• Conrm the digit with the “OK” button.
• The next digit ashes (e.g. “10--).
• Proceed as described in paragraph 2-4 above.
• After conrming the fourth digit with the “OK” but-
ton, the new PIN code is stored. The word “IdLE”
appears on the display.
9.2.2 Setting/changing the date/time (Fig. 23)
m NOTE:
Date and time are necessary settings so that the ro-
botic lawnmower (1) can mow in accordance with the
set mowing schedule.
• The date/time setting is done in the order year -
date - time.
• Press and hold the “START” button for at least 5
seconds.
• The -symbol and “PIN” ash. - symbol and a
number (e.g. 2020) ashes on the display.
• Use the “START”, “HOME” and “OK” buttons to set
the year, similarly to the PIN setting.
• Then the next number illuminates (month.day e.g.
08.25 for 25 August).
• Use the “START”, “HOME” and “OK” buttons to set
the correct month and day.
• The time is displayed last (e.g. 13:25).
• Set the current time as described above.
• After conrming the fourth digit with the “OK” but-
ton, the date and time are stored. The word “IdLE”
appears on the display.
9.2.3 Changing the start time (Fig. 24)
The factory-set start time of 09:00 can be changed
at any time.
• Press and hold the “START” and “OK” buttons si-
multaneously for at least 3 seconds.
• The display shows the set start time, e.g. 13:25,
with the rst digit ashing.
Switching the robotic lawnmower on:
• The robotic lawnmower can then be restarted as
described below.
•
m NOTE:
Before the robotic lawnmower (1) starts mowing, an
acoustic signal (four beeps) is heard, then the blade
disc (6) starts rotating.
• Press the -button (“POWER ON/OFF” button)
until the robotic lawnmower (1) switches on.
• For the rst use, enter the default PIN code “0000”
by pressing “OK” four times when the number “0”
ashes. (The PIN code can be changed as de-
scribed in point 9.2.1).
• After conrming the fourth digit with the “OK but-
ton”, the robotic lawnmower is ready for use. The
word “IdLE” appears on the display.
m NOTE:
The robotic lawnmower (1) switches o automatically
after 30 seconds if no input is made.
m ATTENTION!
If the PIN code is entered incorrectly 10 times, “LOCK”
appears on the display. The device is now locked for
10 minutes before you can enter the PIN code again.
• Press the “START” button and then the “OK” button
to start mowing.
• If you press the “HOME” button and then the “OK”
button, the robotic lawnmower (1) returns to the
charging station (10) with the mowing function
switched o.
The robotic lawnmower (1) operates continuously un-
til the battery charge is too low. The robotic lawnmow-
er automatically returns to the charging station (10).
The cutter disc is deactivated in this state.
m NOTE:
After the battery is fully charged, the robotic lawn-
mower starts again. Alternatively, the robotic lawn-
mower remains in the charging station (10) in accord-
ance with the set mowing schedule.
(By default, the robot mows from Monday to Friday
from 09:00 - 15:00 hrs)
9.2. Settings
m NOTE:
To make adjustments to the product, the robotic lawn-
mower (1) must be switched on. Switch on the robotic
lawnmower (1) by pressing and holding the -button
(“POWER ON/OFF” button) until “PIN” appears on
the display.
To Next Page
Loading...