Precor M9.41si - Creating Custom Courses.19

Creating Custom Courses
CAUTION: After pressing ENTER, clear an
existing custom course profile by simulta¬
neously pressing both f/ie INCLINEfA. keys for
at least 3 seconds. The course profile reverts to
a blinking line at OYo incline. Be cautious about
performing this procedure. Once you clear an
exisdng course profile, you cannot retrieve it.
You can program the M9.41si and create your own course profiles using the two custom courses
(“CUST1” and “CUST2”). Programming a custom course is easy. You just create the custom
courses as you work out by determining the speed and incline for each 0.1 mile segment a ong the
8 S nSmum course lenotn. Speed and incline settings are saved once every .1 a mile winch
eq^ls ToTts onThe displ^. On<!e you complete your workout, the course ,s stored ,n memory
and can be automatically recalled using the same program number.
To create a custom course, follow the steps in Working Out on the M9.41si Low Impact Treadmill
and add the following variation.
1. At the “SELECT COURSE” prompt, choose your custom course: eitherCUST 1” or “CUST 2."
Press the ▼ or A keys until you see the desired course, then press ENTER.
Note- After pressing ENTER, a prompt scrolls across the display warning you that the cu^om
bourse SnSe?s ™ e d and inclines. You are not to use the course if you are not tamrlar
with it. The following Instructions assume that you are
However, if you want to use the existing custom course, press SPEED A to begin.
Hold onto the handrail and press the SPEED A key. Step onto the running belt while the speed
^sTor below 1 mph and begin walking. Use the INCLINETA keys to change the coume
profile as you walk. The first time the custom courses appear, the profile appears flat (0 /.
incline) until you change it.
As you move through the course, you can change the course profile by using the ^EED and
INCLINE VA keys on the segment that is blinking. You cannot go back to a segment once
vou move beyond it. However, you can pause by pressing STOP. Prompts appear and scroll
Lross the display asking you to save the course and end your workout, or continue with yo
workout.
Pressing ENTER saves the course profile up to the point (mile or kilometer) where you
Stopped and resets any previously saved program course.
Note- You must program at least .10 mile (10 dots on the display) before YObf h<»
course can be saved otherwise the software reverts back to the «»shngc()urse Man
existing course profile extended beyond the segment where you stopped, it will be
discarded.
Pressing SPEED A starts the running belt and allows you to continue from where you left
off. Be sure to hold onto the handrail before pressing SPEED A.
once you reach the maximum distance of 8 miles, the prompt, "END COURSE" aPP«ars and
scrolls across the display. The running belt slows to a gradual stop, the incline returns to 0 .,
and prompts appear requesting that you save your changes.
1 Save your changes by pressing ENTER. Once you save your custom course, Y"" ^
.___ nsiar anH m/pr hu Rnterino the associated custom course number.
CAUTION: Once you press the INCLINETA.
keys to reset the course proff/e, you cannot
retrieve the old custom course.
leting Custom Courses
existing custom course can be deleted by pressing both INCLINE TA keys when the custom
rse profile appears on the display. Take the following steps to delete a custom course.
w --- r ^
After answering the setup prompts and choosing your custom course, a “CAUTION” message
scrolls across the screen indicating that an existing custom course exists.
When the course profile appears on the display, press both INCLINE TA keys and hold for a
least 3 seconds. A message appears indicating that the custom course profile has b
(0% Incline and 1 mph/kph speed).
page 19