Printronix SL4M User Manual (English)

Other manuals for Printronix SL4M

User Manual308 pages

Reference Manual112 pages

Programmer's Reference Manual60 pages

Questions and Answers:

M
martinezedwinAug 21, 2025
What to do if Printronix Label Maker media moves, but no image prints in ONLINE mode?
- R
  rodney52Aug 21, 2025
  If the Printronix Label Maker media moves but no image prints in ONLINE mode: 1. Ensure the power supply cable has a secure connection to the right side of the printhead. 2. Place the printer offline and print the Checkerboard diagnostic test pattern. If the pattern prints successfully, the problem lies in the communication between the host computer and the printer.
D
Dominic MillerAug 23, 2025
What to do if Printronix Label Maker media and ribbon move, but no image prints in Thermal Transfer mode?
- T
  Travis WrightAug 25, 2025
  If the media and ribbon move but no image prints in Thermal Transfer mode on your Printronix Label Maker: 1. Print the Checkerboard diagnostic test pattern and check that the image appears on the used portion of ribbon. If the image is on the ribbon, the ribbon may be installed with the transfer side against the printhead instead of against the media. 2. The ribbon may be designed for another model printer. 3. The ribbon may not be compatible with the media.
R
Reginald PerezAug 26, 2025
What to do if Printronix Label Maker RFID encoder works, but does not meet expectations?
- C
  Carlos DavisAug 26, 2025
  If your Printronix Label Maker's RFID encoder isn't performing as expected, ensure that both Error Handling and Label Retry are configured to your desired settings within the RFID (or RFID CONTROL) menu.
W
Willie WhiteAug 28, 2025
What to do if Printronix Label Maker tag failed?
- E
  Eugene AlexanderAug 28, 2025
  If a tag fails on your Printronix Label Maker, consider the following: * Ensure the label is properly aligned by performing the Auto Calibrate procedure. * Verify that you're using smart labels with RFID tags correctly positioned. * Try a different RFID tag to rule out a defective tag. * Confirm that the application sends the correct number of digits to the RFID tag.
A
Alan AvilaAug 30, 2025
How to fix Printronix Label Maker no communication between printer and RFID encoder?
- S
  Scott RussellAug 30, 2025
  If your Printronix Label Maker is experiencing communication issues between the printer and the RFID encoder: 1. Ensure that 'Reader' is enabled in the RFID (or RFID CONTROL) menu. 2. Use the RFID Test option (Admin User enabled) to read and display the current RFID tag content. Class 1 RFID tags usually contain a valid entry due to the pre-test process. 3. If the issue persists, the RFID encoder may be disconnected or defective. Contact your authorized service representative.
E
Erica DavisSep 1, 2025
Why Printronix Label Maker RFID (or RFID CONTROL) menu does not appear?
- K
  Karen WeaverSep 1, 2025
  If the RFID (or RFID CONTROL) menu is not visible on your Printronix Label Maker, it indicates that the printer did not detect the RFID encoder at power-up. Your RFID encoder may be disconnected or defective. Contact your authorized service representative.
M
michael65Sep 6, 2025
How to fix Printronix Label Maker attention status indicator is flashing?
- Z
  Zachary WagnerSep 6, 2025
  When the ATTENTION status indicator light is flashing on your Printronix Label Maker: 1. Check the LCD for a specific fault message. Consult Table 15, Fault Messages on page 196, for guidance. 2. Check for an Out-of-Media condition or missing labels. Load the correct media. 3. Ensure the ribbon and label stock are correctly routed.
N
nsnyderSep 8, 2025
What to do if Printronix Label Maker LCD displays 'Invalid Data' and nothing prints?
- N
  Nicole StricklandSep 8, 2025
  If your Printronix Label Maker displays 'Invalid Data' and doesn't print, it means the printer received data without valid commands, often due to an incorrect emulation or SFCC selection. This message persists until new data is received or the printer is taken offline. 1. If the emulation and SFCC are correct, get additional diagnostic information by selecting an option under the “xxx Diagnostics” menu, found under the Emulations menu. 2. Rerun the job after selecting the desired option to get the additional diagnostic information.

Printronix SL4M Specifications

General

Print Resolution	203 dpi
Print Speed	400 cps
Memory	8 MB Flash, 16 MB DRAM
Dimensions	8.3 x 12.2 x 7.9 inches
Weight	11.9 lbs
Type	Industrial Printer
Media Width	4.1 inches
Media Thickness	0.0025" to 0.0100"
Connectivity	USB, Serial, Parallel
Maximum Print Speed	10 ips
Maximum Print Width	4.1 inches
Media Type	Labels, Tags
Resolution	203 dpi
Operating System Compatibility	Windows, Linux
Noise Level	55 dB