EasyManua.ls Logo

Procom BLUE FLAMEMNSD200TBA - User Manual

Procom BLUE FLAMEMNSD200TBA
36 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
VENT-FREE GAS WALL
HEATER
OWNER’S OPERATION AND
INSTALLATION MANUAL
BLUE FLAME MODELS
MNSD100TBA, MNSD200TBA
MNSD300TBA, MNSD100HBA
MNSD200TBA-BB
MNSD300TBA-BB
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,
Monday through Friday or email customerservice@usaprocom.com
PFS
®
US
WARNING: If the information in this manual is not
followed exactly, a re or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other ammable va-
pors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
•
Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re
department.
—
Installation and service must be performed by a quali-
ed installer, service agency or the gas supplier.
WARNING: This appliance is equipped for Natural and
Propane gas. Field conversion is not permitted other than
between natural or propane gases.

Questions and Answers

  • S
    Stacey KeithSep 3, 2025
    Why do I smell gas when my Procom Heater is off?
    • R
      Robert ClineSep 3, 2025
      If you smell gas even when the control knob of your Procom Heater is in the OFF position, it could be due to: * A gas leak. Locate and correct all leaks. * A defective control valve. Replace the control valve.
  • L
    Laura SpencerSep 2, 2025
    Why is my Procom Heater whistling?
    • M
      Michelle ShermanSep 2, 2025
      If your Procom Heater is producing a whistling noise when the burner is lit, here are some possible causes: * The control knob was turned to the high (5) position when the burner was cold. Turn the control knob to the low (1) position and let it warm up for a minute. * There's air in the gas line. Operate the burner until the air is removed from the line. Have the gas line checked by your local gas supplier. * The air passageways on the heater are blocked. Observe the minimum installation clearances. * The burner orifice is dirty or partially clogged. Clean or replace the burner orifice.
  • B
    Billy WrightSep 1, 2025
    Why does my Procom Heater smell bad?
    • K
      Kimberly ConleySep 1, 2025
      If your Procom Heater is producing unwanted odors, consider these possibilities: * The heater might be burning vapors from paint, hair spray, glues, etc. Ventilate the room and stop using odor-causing products while the heater is running. * There could be a gas leak. Locate and correct all leaks. * If it's a propane/LP gas model, the fuel supply might be low. Refill the supply tank.
  • R
    Robert BrownAug 31, 2025
    Why is the flame so yellow on my Procom Heater?
    • B
      Brooke RamirezAug 31, 2025
      If you observe a high yellow flame during burner combustion in your Procom Heater, it may be due to: * Not enough air. Check the burner for dirt and debris and clean it if necessary. * A defective gas regulator. Replace the gas regulator. * Inlet gas pressure being too low. Contact your local gas supplier.
  • J
    John YoungAug 30, 2025
    Why is there a delay when the burner ignites on my Procom Heater?
    • K
      kchavezAug 30, 2025
      If your Procom Heater experiences delayed ignition of the burner(s), the following could be the issue: * The manifold pressure might be too low. Contact your local gas supplier. * The burner orifice could be clogged. Clean or replace the burner orifice.
  • K
    Kelly CostaAug 29, 2025
    What causes burner backfiring in my Procom Heater?
    • J
      Joshua WoodAug 29, 2025
      If the burner is backfiring during combustion in your Procom Heater, it could be caused by: * A clogged or damaged burner orifice. Clean or replace the burner orifice. * A damaged burner. Replace the burner. * A damaged gas regulator. Replace the gas regulator.
  • J
    Jill SmithAug 28, 2025
    Why does my Procom Heater shut off while in use?
    • A
      Anthony AlexanderAug 28, 2025
      If your Procom Heater shuts off during use and the ODS operates, consider the following: * There might not be enough fresh air available. Open a window or door for ventilation. * The line pressure could be low. Contact your local gas supplier. * The ODS/pilot may be partially clogged. Clean the ODS/pilot.
  • T
    tracyrodriguezAug 27, 2025
    Why do I smell gas when my Procom Heater is running?
    • M
      meagan70Aug 27, 2025
      If you notice a gas odor during combustion with your Procom Heater, it could be due to: * Foreign matter between the control valve and burner. Disassemble the gas tubing and remove any foreign matter. * A gas leak. Locate and correct all leaks.
  • M
    Matthew TaylorAug 26, 2025
    Why won't the burner light on my Procom Heater after the pilot is lit?
    • R
      Randall WalkerAug 27, 2025
      If the burner(s) on your Procom Heater don't light after the ODS/pilot is lit, the following could be the cause: * The burner orifice may be clogged. Clean or replace the burner orifice. * The burner orifice diameter might be too small. Replace the burner orifice. * The inlet gas pressure could be too low. Contact your local gas supplier.
  • K
    Kathryn WiseAug 25, 2025
    What to do if there is no spark when pressing the ignitor button on my Procom Heater?
    • K
      Keith JohnsonAug 26, 2025
      If there's no spark at the ODS/pilot when you press the ignitor button on your Procom Heater, here's what could be happening: * The ignitor electrode might be positioned incorrectly or broken. Replace the pilot assembly. * The ignitor electrode may not be connected to the ignitor cable. Replace the ignitor cable. * The ignitor cable could be pinched or wet. Free the ignitor cable if it's pinched and keep it dry. * The ignitor cable might be broken. Replace the ignitor cable. * The piezo ignitor could be bad. Replace the piezo ignitor.

Procom BLUE FLAMEMNSD200TBA Specifications

General IconGeneral
BrandProcom
ModelBLUE FLAMEMNSD200TBA
CategoryGas Heater
LanguageEnglish

Related product manuals