EasyManua.ls Logo

Procom ML100HBAHR - User Manual

Procom ML100HBAHR
32 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
BLUE FLAME VENT-FREE
PROPANE/LP GAS HEATER
OWNER’S OPERATION AND
INSTALLATION MANUAL
MODELS
ML100HBAHR
ML100TBAHR
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,
Monday through Friday or email customerservice@usaprocom.com
WARNING: If the information in this manual is not
followed exactly, a re or explosion may result causing
property damage, personal injury or loss of life.
Do not store or use gasoline or other ammable va-
pors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use any
phone in your building.
Immediately call your gas supplier from a neighbors
phone. Follow the gas suppliers instructions.
If you cannot reach your gas supplier, call the re
department.
Installation and service must be performed by a quali-
ed installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
10,000 BTU/Hr
Thermostatically-Controlled Heater

Questions and Answers

  • M
    Michael YoderSep 16, 2025
    Why is my Procom ML100HBAHR Gas Heater burner backfiring?
    • T
      Tiffany WillisSep 16, 2025
      If you notice burner backfiring during combustion in your Procom Gas Heater, it could be due to a clogged or damaged burner orifice, so clean or replace it. The burner itself might be damaged. A defective gas regulator can also cause backfiring, so replace the gas regulator.
  • W
    wardaliciaAug 25, 2025
    Why does my Procom Heater keep shutting off?
    • A
      April ShieldsAug 25, 2025
      If your Procom Heater shuts off during use (ODS operates), it could be due to not enough fresh air being available, low line pressure, or a partially clogged ODS/pilot. To address this, open a window or door for ventilation. You may also need to contact your local gas supplier to check the line pressure and clean the ODS/pilot.
  • T
    Theodore PeckAug 25, 2025
    Why is there a gas odor when my Procom Heater is on?
    • K
      kelly60Aug 26, 2025
      If you smell gas during combustion in your Procom Heater, there might be foreign matter between the control valve and burner, or there could be a gas leak. You can take apart the gas tubing and remove any foreign matter. Also, locate and correct all gas leaks.
  • E
    eboyleAug 27, 2025
    Why does the pilot light go out when I release the knob on my Procom Heater?
    • Z
      zpetersAug 27, 2025
      If the ODS/pilot lights but the flame goes out when you release the control knob on your Procom Heater, make sure the control knob is fully pressed in and held for at least 30 seconds after the pilot lights. Ensure the equipment shutoff valve is fully open. Check that the thermocouple connection is snug at the control valve, and hand-tighten it a quarter turn more. If the pilot flame isn't touching the thermocouple, it may be due to low gas pressure or a dirty ODS/pilot. Contact your gas company or clean/replace the ODS/pilot assembly. If the thermocouple or control valve is damaged, replace them.
  • T
    tbergerSep 18, 2025
    Why is there a yellow flame during burner combustion in my Procom ML100HBAHR?
    • T
      Troy MartinSep 18, 2025
      If you see yellow flame during burner combustion in your Procom Gas Heater, it could be due to not enough air. Check the burner for dirt and debris and clean it if necessary. A defective gas regulator can also cause this issue, so replace it. Additionally, the inlet gas pressure might be too low, so contact your local propane/PL gas company.
  • K
    Kelly WoodSep 23, 2025
    Why is there white powder around my Procom ML100HBAHR?
    • N
      Nathaniel RogersSep 23, 2025
      If you notice a white powder residue forming within the burner box or on adjacent walls or furniture when using your Procom Gas Heater, it is likely due to vapors from furniture polish, wax, carpet cleaners, etc., turning into white powder residue when heated. Turn off the heater when using these products.
  • B
    Brian JohnsonSep 8, 2025
    What to do if the pilot light goes out when releasing the control knob on my Procom ML100HBAHR Gas Heater?
    • C
      Courtney PerrySep 8, 2025
      If the ODS/pilot lights on your Procom Gas Heater, but the flame goes out when you release the control knob, ensure the control knob is fully pressed in and held for at least 30 seconds after the pilot lights. Also, make sure the equipment shutoff valve is fully open. A loose thermocouple connection at the control valve can also cause this issue; hand tighten it until snug, then tighten an additional 1/4 turn. If the pilot flame isn't touching the thermocouple, it may cool down and cause the flame to go out. In this case, you can clean the ODS/pilot or replace the ODS/pilot assembly. Lastly, a damaged thermocouple should be replaced.
  • B
    brianacastroSep 9, 2025
    Why is there a gas odor during combustion in my Procom ML100HBAHR?
    • N
      Nicole MccoySep 9, 2025
      If you smell gas during combustion with your Procom Gas Heater, it is likely due to a gas leak. You should locate and correct all leaks.
  • T
    Timothy ScottSep 3, 2025
    Why does my Procom Heater make a clicking noise?
    • M
      Mrs. Pamela Ramirez MDSep 3, 2025
      This is a common occurrence due to metal expanding while heating or contracting while cooling. If the noise is excessive, contact a qualified service technician.
  • V
    Victor LongSep 1, 2025
    Why aren't the burner plaques glowing on my Procom Heater?
    • W
      william31Sep 1, 2025
      If the burner plaque(s) on your Procom Heater does not glow, the plaque may be damaged, the inlet gas pressure may be too low, or the control knob may be set between locked positions. Replace the burner. If the gas pressure is too low, contact your local gas company. Ensure the control knob is locked at the desired setting.

Procom ML100HBAHR Specifications

General IconGeneral
BrandProcom
ModelML100HBAHR
CategoryGas Heater
LanguageEnglish

Related product manuals