Project EV EVA-07S-SE-C - Downloading the right app for you; DOWNLOAD THE PROJECT EV STANDARD APP; DOWNLOAD THE ELECTRIC MILES INSTALLER APP; DOWNLOAD THE ELECTRIC MILES SMART CHARGING APP

5LJKWFOLFNRQ/RFDO$UHD&RQQHFWLRQDQGFOLFNRQ3URSHUWLHV
6HOHFW,QWHUQHW3URWRFRO9HUVLRQ7&3,3YDQGFOLFNRQ3URSHUWLHV
6HOHFW8VHWKHIROORZLQJ,3DGGUHVVDQGHQWHUWKH,3DGGUHVV6XEQHW0DVN'HIDXOW
*DWHZD\&OLFN2.DQGFORVHWKH/RFDO$UHD&RQQHFWLRQSURSHUWLHVZLQGRZ
F &KHFN ZKDW ZHE EURZVHU LV EHLQJ XVHG LW¶V VXJJHVWHG WR XVH )LUHIR[ RU ,( &KURPH
FDQQRWEHXVHGWRXSGDWHILUPZDUH
G &KHFN LI\RX KDYHLQSXW WKHFRPSOHWH FRQWHQWZKLFK LVKWWSLQWKH
DGGUHVVILHOGGRQRWOHDYHRXWWKHKWWSRUWKH³´
H 6RPHWLPHV\RXPD\QHHGWRUHVWDUWWKHFKDUJHUWRDFFHVVLWVSDUDPHWHUVHWWLQJSDJH
I ,I \RX KDYH FKDQJHG WKH FKDUJHU¶V ,3 WR RWKHU YDOXH DQG FDQQRW UHPHPEHU \RX FDQ
UHVWRUHWKHFKDUJHUWRIDFWRU\VHWWLQJE\ORQJSUHVVWKHUHVHWEXWWRQ7KHQ\RXFDQDFFHVV
LWXVLQJKWWS
3
OHDVHQRWH$IWHUUHVWRULQJWKHFKDUJHUWRIDFWRU\VHWWLQJ\RX¶OOQHHGWRUHVHWWKHFKDUJHU
,'DQGVHUYHUXUORWKHUZLVHWKHFKDUJHUZRQ¶WEHFRQQHFWHGWRWKHEDFNRIILFHVHUYHU
 
5HVHWEXWWRQ
(3). Right-click on Local Area Connection and click on Properties.
(4). Select Internet Protocol Version 4 (TCP/IPv4) and click on Properties.
(5). Select “Use the following IP address” and enter the IP address, Subnet Mask,
Default Gateway. Click OK and close the Local Area Connection properties window.
c. Check which web browser is being used, it’s suggested you use Firefox or IE.
Chrome cannot be used to update rmware.
d. Check if you have input the complete path, which is http://192.168.1.5:8080, in the
address eld, do not leave out the http:// or the“:8080”.
e. You may need to restart the charger to access its parameter setting page.
f. If you have changed the charger’s IP to another value but cannot remember it, you
can restore the charger to factory setting by pressing and holding the reset button.
Then you can access it using http://192.168.1.5:8080.
Please note: After restoring the charger to factory setting, you need to reset the
charger ID and server url, or the charger won’t be connected to the back-oce server.
32 33
Downloading the
right app for you
Power flow management
Load balancing feature
Multiple mode control
(via app, plug and go, RFID swipe card)
With our bespoke app, you can remotely set your charger or
chargers to only provide power during off-peak hours, allowing for
charging at a much lower energy tariff, saving you money. Our
simple, intuitive UI means seamless guiding through multiple
charging modes and time settings.
DOWNLOAD THE PROJECT EV STANDARD APP DOWNLOAD THE PROJECT EV STANDARD APP
DOWNLOAD THE ELECTRIC MILES INSTALLER APP DOWNLOAD THE ELECTRIC MILES INSTALLER APP
Static/Dynamic Load
management
Pairs charger to network
New/Existing Builds
Set spending caps
Smart Charging
Optimise based
on tariff
DOWNLOAD THE ELECTRIC MILES SMART CHARGING APP DOWNLOAD THE ELECTRIC MILES SMART CHARGING APP
Electric Miles
available on
Save money and reduce your carbon footprint with
reliable and smart EV charging. Project EV are
working with Electric Miles to provide drivers with
an easy-to-use and market leading smart charging
experience.
Configuring a Project EV charging site has never
been easier. All you need is a phone with the
Installer Miles app to set up existing and new
sites with load management and charger
connectivity over hotspot.
Installer Miles available on
22
Please note: Using the Electric Miles App makes
the Project EV App obsolete and control of the
charger through the Project EV App will no
longer be possible.
Please note: Using the Electric Miles App makes
the Project EV App obsolete and control of the
charger through the Project EV App will no
longer be possible.