To Next PageTo Next PageWhat to do if the Project Source toilet remote is not working?
If the Project Source toilet remote isn't working, the most common cause is that the batteries need to be replaced. Try replacing the batteries in the remote.
Why is my Project Source toilet not spraying water?
If your Project Source toilet is not spraying water, there are several potential causes: * The angle valve may not be opened enough. Solution: Open the angle valve or adjust its openness. * The water level might be set too low. Solution: Increase the water level to a higher setting. * The inlet water strainer could be blocked. Solution: Clean the strainer. * The spray tip hole might be blocked. Solution: Clean or replace the spray tip.
How to fix a crashed Project Source toilet?
If your Project Source toilet stops working, it may be because the outlet isn't properly connected to the power supply, or the plug isn't fully inserted. Check that the power cord is plugged in correctly. Then, press the reset button until the indication light turns on. Also, if there was a power outage, use the remote or side buttons to power the toilet back on.
What to do if Project Source toilet has a water leakage?
If your Project Source toilet has a water leakage, it is likely due to the angle valve, inlet water pipe, or water distributor not being properly connected. Reconnect these components to resolve the issue.
Why is the Project Source toilet seat temperature not warm?
If the Project Source toilet seat is not warm, it might be set to Normal Temperature or the toilet is in idle mode. To fix this, readjust the seat temperature to a higher setting.
What to do if outage flush is not working in Project Source toilet?
If the outage flush is not working on your Project Source toilet, it is likely because the back-up batteries are either not installed or have failed. Install or replace the back-up batteries to resolve this.
How to fix a loose lid on Project Source toilet?
If the lid on your Project Source toilet feels loose, it's probably due to loose bolts on the seat. Simply re-tighten the bolts to secure the lid.
Describes the rear wash spray function, including oscillating movement.
Explains the front wash spray function and its oscillating movement.
Details the warm air drying function and adjustable air outlet position.
Covers seat soft closing and adjustable water pressure.
Illustrates the basic function buttons located on the side of the toilet.
Lists all items included in the product package for unboxing.
Details T-bolts, washers, nuts, wax ring, and angle valve for installation.
Lists batteries for power and other essential components.
Explains the meaning of warning and caution symbols for safe operation.
Lists actions that must not be performed to prevent hazards and injury.
Lists essential actions to ensure safe use and prevent damage.
Covers precautions regarding the power cord, plug, and electrical outlets.
Details requirements for grounding and circuit breakers for electrical safety.
Lists cautions for using the toilet, cleaning, and handling water to prevent damage.
Outlines initial steps for checking parts before assembly.
Verifies bathroom conditions, draining, and water/electricity routes for installation.
Guides on installing the angle valve for proper water supply connection.
Lists general warnings for installing the toilet to avoid damage and injury.
Details how to remove the toilet seat to access components for installation.
Explains placing the wax ring and securing the toilet to the floor flange.
Describes reconnecting the water connection hoses to the toilet seat.
Details connecting the water inlet hose to the angle valve.
Instructions for installing the remote control bracket on the wall for easy access.
Guides on turning on water and linking the power supply to activate the unit.
Distinguishes between operation, idle, standby modes and sit-down sensor activation.
Explains how to adjust water pressure and nozzle cleaning position.
Describes the rear wash and front wash operations, including oscillating cleansing.
Details starting and adjusting the warm air dryer and activating the fan.
Describes specific wash modes for women and strong cleaning with adjustable pressure.
Explains 4 settings for adjusting water temperature for user comfort.
Describes 4 settings for adjusting seat temperature, including automatic lowering.
Details specific wash modes for children and a combined cleaning cycle.
Covers flush operations, night light control, and power saving modes.
Details basic functions like flush, dryer, and washes accessible via side buttons.
Explains the meaning of different buzzer sounds from the toilet for fault indication.
Addresses common issues like no spray, weak pressure, or water leakage with solutions.
Provides guidance on cleaning the toilet housing and seat for optimal performance.
Describes how to clean the wash nozzles using a brush.
Details the process for turning off water and cleaning the water inlet strainer.
Covers cleaning the strainer and reinstalling it properly.
Explains how to replace batteries in the remote control and code matching.
Guides on replacing the toilet's internal back-up batteries.
Outlines the warranty terms, conditions, and exclusions for the product.
Details voltage, power, water pressure, and flushing capabilities.
Lists specifications for seat heating, drying temperatures, and fan functions.
Provides product dimensions, weight, and average water consumption data.
General| Brand | Project Source |
|---|---|
| Model | MT-25005L |
| Type | Two-piece |
| Bowl Shape | Elongated |
| Color | White |
| Material | Vitreous china |
| Rough-In Size | 12 inches |
