To Next PageTo Next Page
Need help?Do you have a question about the ProMinent Beta b BT4b Series and is the answer not in the manual?
General| Brand | ProMinent |
|---|---|
| Model | Beta b BT4b Series |
| Category | Water Pump |
| Language | English |
Provides additional context and explanations for using the operating instructions.
Safety information is identified by pictograms.
Conforms to current EU regulations.
Importance of identity code for service and parts.
Details product range, type, and capacity specifications.
Describes the features and benefits of the Beta b pump.
Explains signal words and warning signs used in the manual.
Illustrates warning signs and defines proper/prohibited pump uses.
Alerts on personal damage, electric shock, hazardous chemicals, fire, and substances.
Addresses chemical spraying, injury risks, and incorrect metering hazards.
Covers illegal operation, emergency info, and personnel qualifications.
Warnings related to transporting pumps and repair returns.
Specifies environmental limits and items included in delivery.
Identifies major components of the pump and liquid end.
Details control buttons, switches, and indicators.
Explains pulse switch, stroke adjustment, and multifunctional switch.
Explains LED indicators and details external control/level switch terminals.
Explains the working principle of the liquid end and the drive unit.
Details capacity determination and self-bleeding capabilities.
Lists selectable operating modes (Manual, External Contact, External Analogue).
Explains relay options and priority of operating modes/statuses.
Warns about electric shock and risks from improper operation/maintenance.
Explains causes for low capacity related to valve orientation and vibration.
Cautions on chemical spraying, damage, and component safety.
Guidelines and safety for installing hose lines without bleed valves.
Instructions for installing stainless steel pipes for SS designs.
Notes for pumps with bleed valves and return line setup.
Specifics for installing SEK pumps, including priming.
General safety and component protection notes for hydraulic installation.
Warnings on electric shock and preventing damage from power surges.
Details for connecting mains voltage, including inductive loads.
Safety and voltage limits for low voltage connections.
Details of the "External control" terminal.
Specs for Pause, External Contact, mA input, and cable assignments.
Details for level switch terminal and relay types.
Functionality of the fault indicating relay output (identity code 1+3).
Functionality of combined fault and pacing relay outputs (identity code 4+5).
Warns about chemical reactions with water and fire hazards.
Precautions for handling hazardous feed chemicals and preventing spraying.
Step-by-step guide for starting the pump, including tightening torque and filling.
Startup steps for pumps with bleed valves and self-bleeding types.
Guidance on setting stroke length and rate for accurate dosing.
Electrical safety warnings for installed options and housing during operation.
Details manual operation procedures, including capacity adjustment.
Details operation in "Extern Contact" mode.
Details external analogue and remote control options.
Safety warnings before maintenance, and precautions for chemical spraying.
Quarterly maintenance tasks for standard liquid ends.
Quarterly maintenance tasks for liquid ends with bleed valves.
Specifies tightening torque for screws during maintenance.
Warns against unauthorized repairs and covers electrical, chemical, and fire safety.
Procedure for cleaning discharge and suction valves.
Step-by-step guide for replacing the pump diaphragm.
Lists faults and remedies for pumps not priming.
Describes fault and warning messages indicated by LEDs and pump stops.
Safety warnings and procedures for decommissioning the pump.
Environmental hazard warnings and proper disposal methods.
Provides pump capacity at different pressures and stroke rates.
Details accuracy for liquid ends and suitable viscosity ranges.
Details materials and electrical data for the pump.
Specifies storage, transport, and operating temperature/humidity limits.
Covers protection ratings, compatibility, sound level, and shipping weight.
Provides dimensions for the PP material version.
Provides dimensions for the NP material version.
Provides dimensions for PP/NP SEK versions.
Provides dimensions for the PV material version.
Provides dimensions for TT and PV HV material versions.
Provides dimensions for the SS material version.
Capacity charts for various Beta b models based on stroke length and rate.
Visual breakdown of pump components for identification.
Information on ordering retrofit kits and finding further details online.
