ProMinent Beta BT4b User Manual

Beta
®
b BT4b and BT5b Solenoid Metering Pump
Operating Manual
Two sets of operating instructions are required for the safe, correct and proper operation of the dosing pumps: The product-
specific operating instructions and the
"General Operating Instructions ProMinent® Solenoid Metering Pumps".
Both sets of operating instructions are only valid when read together.
Part no. 986356 BA BE 022 05/09 GB
Please carefully read these operating instructions before use! · Do not discard!
The operator shall be liable for any damage caused by installation or operating errors
!
Technical changes reserved.

ProMinent Beta BT4b Specifications

General

Stroke Length	Adjustable
Protection Class	IP65
Power Supply	230 V, 50/60 Hz
Control	Manual
Materials	PVDF, PTFE, EPDM, Ceramic
Operating Temperature	0 - 40 °C
Storage Temperature	-20 to 60 °C

Summary

Identcode

Safety Chapter

Explanation of the safety information

Explains signal words and warning signs used to denote hazard severity in the manual.

Warning signs denoting different types of hazard

Illustrates warning signs and their corresponding hazard types.

Correct and Proper Use

Outlines the correct and proper usage guidelines for the dosing pump.

Safety information

Provides specific warnings regarding hazardous chemicals, incorrect operation, and personal damage.

Information in the event of an emergency

Details actions to take in case of electrical accidents or chemical leaks.

Qualification of personnel

Defines the qualifications required for personnel performing specific tasks on the pump.

Storage, Transport and Unpacking

Safety information

Warns against shipping radioactive media and returning pumps for repair.

Overview of the Device and Control Elements

5.1 Overview of the Device

Provides a general overview of the pump's main components.

5.2 Control Elements

Details the various control elements on the pump's front panel.

5.2.4 Functional and Fault Indicators

Explains the meaning of the fault, warning, and operating indicator LEDs.

5.2.5 "External Control" Terminal

Describes the five-pole terminal for external control functions and modes.

Functional Description

6.3 Capacity

Explains how capacity is determined by stroke length and rate.

6.5 Operating Modes

Introduces different operating modes selectable via the multifunctional switch.

6.8 Hierarchy of Operating Modes, Functions and Fault Statuses

Shows the order of priority for operating modes, functions, and fault statuses.

Electrical Installation

7.1 Supply Power Connection

Details how to connect the pump to the mains power supply.

7.2 Description of the Terminals

Introduces the description of the pump's terminals.

7.2.1 "External Control" Terminal

Describes the five-pole terminal for external control functions and modes.

7.2.2 "Level Switch" Terminal

Describes the terminal for connecting a 2-stage level switch.

7.3.1 "Fault Indicating Relay" Output (Identity Code 1 + 3 or 4 + 5)

Explains the fault indicating relay option and its function for alerts.

Operation

8.1 Manual

Details the manual operation mode of the pump.

8.1.1 Capacity

Explains how to set capacity using stroke length and rate.

8.1.2 Functions

Lists and describes available pump functions like Pause, Stop, and Priming.

8.1.3 Extern Contact

Describes the 'Extern' operating mode for external signal control.

Maintenance

Standard liquid ends Maintenance Tasks

Lists quarterly maintenance tasks for standard liquid ends including checks on diaphragm, valves, and connections.

Liquid Ends with Bleed Valve Maintenance

Lists quarterly maintenance tasks for liquid ends with a bleed valve.

Repair

10.1 Cleaning Valves

Provides instructions for cleaning discharge and suction valves.

Cleaning Discharge/Suction Valves (Types 1000-2504)

Details cleaning procedures for discharge and suction valves on specific pump types.

Cleaning Discharge/Suction Valves (Types 0708-0232)

Details cleaning procedures for discharge and suction valves on other specific pump types.

10.2 Replacing the Diaphragm

Provides instructions for replacing the pump's diaphragm.

Troubleshooting

11.1 Faults without Fault Alert

Lists common faults without fault alerts, their causes, solutions, and personnel.

11.2 Fault Alerts

Lists fault alerts, their causes, solutions, and responsible personnel.

11.3 Warning Alerts

Lists warning alerts, their causes, solutions, and responsible personnel.

11.4 All Other Faults

Decommissioning

Disposal

Technical Data

13.1 Performance Data

Provides minimum flow rates at different pressures and connection sizes.

13.2 Accuracy

13.2.1 Standard Liquid End

13.4 Material Data

13.5 Electrical Data

13.6 Ambient Conditions

13.6.1 Temperatures

Appendix

14.1 Dimensional Drawings

Dimensional drawing of Beta® b, NP material version

Dimensional drawing of Beta® b, PP and NP SEK material version

Dimensional drawing of Beta® b, PV material version

Dimensional drawing of Beta® b, PV HV material version

Dimensional drawing of Beta® b, TT material version

Dimensional drawing of Beta® b, SS material version

14.2 Diagrams for Setting the Capacity

Provides diagrams for setting pump capacity based on stroke length and rates.

14.3 Exploded Views of Liquid Ends

Beta® 1000 - 1604 PP liquid end with bleed

Beta® 0708 (1008) - 0220 (0420) PP liquid end with bleed

Beta® 0232 PP liquid end without bleed valve

Beta® 1000 - 1604 NP liquid end with and without bleed valve

Beta® 0708 (1008) - 0220 (0420) NP liquid end with and without bleed valve

Beta® 0232 NP liquid end with and without bleed valve

Beta® 1000 - 1604 PV liquid end with bleed valve

Beta® 0708 (1008) - 0220 (0420) PV liquid end with bleed valve

Beta® 0232 PV liquid end without bleed valve

Beta® 1604-0220 (0420) PV HV liquid end, for highly viscous feed chemicals

Beta® 1000 - 1604 TT liquid end

Beta® 0708 (1008) - 0220 (0420) TT liquid end

Beta® 0232 TT liquid end

Beta® 1000 - 1604 SS liquid end

Beta® 0708 (1008) - 0220 (0420) SS liquid end

Beta® 0232 SS liquid end

Beta® 1601 - 1604 PP SEK and 1601 - 1604 NP SEK liquid end, self-bleeding

Beta® 0708 (1008) - 0220 (0420) PP / NP SEK liquid end, self-bleeding

14.4 Ordering Information

Spare parts sets for SEK types

Spare parts sets for other types

14.5 Retrofitting Relays

Fitting the relay board