Quadra-Fire PELLET INSERT CB1200I User Manual

R
www.quadrare.com
7014-188B
February 3, 2010
CB1200-I PELLET INSERT
Owner’s Manual
Installation and Operation
CB1200MI-MBK
Model:
DO NOT DISCARD THIS MANUAL
NOTICE
• Important operating and
maintenance instruc-
tions included.
• Leave this manual with
party responsible for use
and operation.
• Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
DO NOT
DISCARD
WARNING
Please read this entire manual
before installation and use of this
pellet fuel-burning room heater.
Failure to follow these instructions
could result in property damage,
bodily injury or even death.
• Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of this
or any other appliance.
•
Do not overre - If any external part starts to
glow, you are overring. Reduce feed rate.
Overring will void your warranty.
•
Comply with all minimum clearances to com-
bustibles as specied. Failure to comply may
cause house re.
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and national
codes and regulations.
• Consult local building, re ofcials or authorities having jurisdic-
tion about restrictions, installation inspection, and permits.
CAUTION
Tested and approved for wood pellets and shelled
eld corn fuel only. Burning of any other type of fuel
voids your warranty.
CAUTION
O-T L
Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
WARNING
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
HOT SURFACES!
Glass and other surfaces are
hot during operation AND
cool down.

Quadra-Fire PELLET INSERT CB1200I Specifications

General

Type	Pellet Insert
Fuel Type	Pellets
Efficiency	Up to 85%
Hopper Capacity	60 lbs
Burn Time	Up to 48 hours
BTU Input	Up to 40, 000 BTU
Ignition	Automatic
Warranty	Limited Lifetime Warranty
Venting	Direct Vent

Summary

Safety and Notices

Hot Surface Warning

Hot glass and surfaces can cause burns during operation and cool down.

Building Code Compliance Caution

Check and comply with all local, regional, state, and national codes.

1 Listing and Code Approvals

Appliance Certification

Details of testing and listing for the appliance.

Mobile Home Approval

Requirements for installation in mobile homes.

2 Getting Started

Design, Installation & Location Considerations

Planning appliance placement and clearances for safety and performance.

Appliance & Chimney Location

Factors affecting appliance and chimney performance.

Negative Pressure Issues

Causes and solutions for negative pressure affecting appliance.

Fire Safety Precautions

Essential safety measures for fire prevention.

Pre-Use Inspection Checklist

3 Dimensions and Clearances

Appliance Dimensions

Clearances to Combustibles (Built-In)

Required clearances for built-in installations.

Clearances for Masonry/Zero Clearance

Clearances for masonry and zero clearance fireplaces.

Minimum Opening Requirements

Floor Protection Standards

4 Vent Information

Chimney & Exhaust Connections

Guidance on connecting the appliance to venting systems.

Vent Termination Requirements

Rules for proper placement of vent terminations.

5 Venting Systems

Horizontal Reline with Outside Air

Vertical Reline with Outside Air

6 Mobile Home Installation

Mobile Home Installation Requirements

Specific requirements for installing in a mobile home.

7 Appliance Set-Up

Rear Shroud Installation

Outside Air Kit Instructions

Thermostat Installation

8 Operating Instructions

Fuel Size, Material & Storage

Proper selection, handling, and storage of fuels.

General Operating Information

Before Your First Fire

Starting Your First Fire

Step-by-step guide for lighting the first fire.

Feed Rate Adjustment

9 Troubleshooting

Appliance Not Responding

Diagnosing and fixing power or response issues.

No Fire or Fuel Issues

Troubleshooting no fire, fuel delivery, or ignition problems.

Slow or Smoky Start-Up

Blower or Feed System Failures

Start Sequence or Shutdown Problems

10 Maintaining & Servicing Appliance

Proper Shutdown Procedure

Steps for safely shutting down the appliance.

General Maintenance Procedures

Cleaning Firepot & Tools

Ash Removal & Disposal

Heat Exchanger & Exhaust Cleaning

High Ash Fuel Content Maintenance

Glass Replacement

Instructions for safely replacing the appliance glass.

Igniter & Baffle Replacement

11 Reference Materials

Warranty Policy

Details of the manufacturer's limited lifetime warranty.