Why is my Radio Shack PRO-135 Scanner on but not scanning?
If your Radio Shack Scanner is on but not scanning, it might be due to the squelch not being adjusted correctly. Try adjusting the squelch. Alternatively, only one or no channels may be stored; store frequencies into more than one channel to resolve this.
Why won’t my Radio Shack Scanner work at all?
If your Radio Shack Scanner is not working at all, ensure it's receiving power by either recharging the rechargeable batteries or replacing the non-rechargeable batteries. Also, verify that the AC adapter or DC adapter is properly connected to the DC 9V 300 mA jack.
What to do if the keypad doesn’t work on my Radio Shack Scanner?
If the keypad on your Radio Shack Scanner isn’t working, it's possible that the keylock function is activated. To deactivate it, press and hold /KEYLOCK until the keylock indicator disappears.
What to do if the signal is flashing on my Radio Shack PRO-135 Scanner?
If your Radio Shack Scanner displays a flashing signal, it likely indicates that the batteries are low. To resolve this, recharge the rechargeable batteries or replace the alkaline batteries.
How to fix poor reception on Radio Shack PRO-135 Scanner?
If you're experiencing poor or no reception on your Radio Shack Scanner, first check the batteries. Weak or completely discharged batteries can cause this issue, so ensure they are checked or that the AC adapter or DC adapter is connected properly. Also, make sure an antenna is connected to the scanner, as a loose antenna can also lead to poor reception.
What to do if 'Error' appears on Radio Shack PRO-135?
If an error appears on your Radio Shack Scanner, it indicates a programming error. Re-enter the frequency correctly, making sure to include the decimal point.
Explains the functions and operation of the scanner's keys and controls.
Instructions on how to attach the scanner's antenna for proper reception.
Guide on how to attach the belt clip for portable use.
Details on how to power the scanner using batteries or an AC adapter.
Step-by-step guide for inserting AA batteries correctly into the scanner.
Important information and warnings regarding battery usage and care.
Information on how to properly recycle rechargeable batteries.
Instructions for connecting and using an external AC power adapter.
How to connect headphones for private listening and their effect on the speaker.
Guidelines for safe listening practices to protect hearing while using the scanner.
Explains basic terms and concepts used throughout the manual.
Lists known internal scanner frequencies that may cause interference.
Step-by-step instructions for powering on the scanner correctly.
Detailed guide on how to enter and store radio frequencies into memory channels.
How to search through preset or custom frequency ranges for active transmissions.
Steps to initiate a limit search and control its direction.
Instructions for defining the upper and lower frequency limits for a search.
How to search up or down from a specific frequency for transmissions.
Searching pre-programmed frequency banks like Ham, Marine, Aircraft, and Police.
Procedure for saving discovered frequencies into memory channels.
How to skip unwanted frequencies during a search to improve efficiency.
Information on the different search speeds available (Normal and Hypersearch).
Introduction to the Signal Stalker feature for detecting strong transmissions.
Steps to activate, use, and deactivate the Signal Stalker feature.
How to configure various settings for the Signal Stalker feature.
Instructions on how to initiate scanning through programmed channels and banks.
How to directly access and monitor a specific channel without scanning.
Procedure for scanning NOAA weather transmissions.
How to activate and receive weather alert signals.
How to test the weather alert alarm functionality.
Instructions for accessing the Skywarn weather net frequencies.
Explanation of the Skywarn program and the types of weather reports it uses.
How to enable or disable the 2-second delay for transmissions.
How to enable or disable specific banks of stored channels for scanning.
How to prevent the scanner from stopping on specific unwanted channels.
How to set a priority channel to monitor while scanning other channels.
How to lock the keypad to prevent accidental changes.
How to manually turn on the display backlight for visibility.
How to configure the backlight to activate automatically when signals are received.
How to set the backlight to illuminate when the scanner is powered on.
How to enable or disable the audible tone when pressing scanner keys.
How to enable the battery save feature to conserve power.
Instructions for copying programmed data to another scanner using a cable.
How to upload or download scanner data to/from a computer via a cable.
Important regulatory information regarding radio interference and compliance.
Information on what transmissions are legal and illegal to monitor.
Guidelines for cleaning, handling, and storing the scanner to ensure longevity.
What to do if the scanner malfunctions and how to seek assistance.
Detailed technical specifications of the scanner's performance and capabilities.
Common problems, their causes, and solutions for scanner malfunctions.
Procedure to reset the scanner to factory default settings if it locks up.
General| Type | Handheld Scanner |
|---|---|
| Channels | 200 |
| Modulation | AM, FM, WFM |
| Antenna | Telescopic |
| Channel Steps | 5, 12.5 kHz |
| Power | 6V |
To Next Page