To Next PageTo Next PageHow to unlock keypad on Radio Shack PRO-106?
If the keypad on your Radio Shack Scanner isn't working, it might be locked. Try pressing the FUNC KEY/ LIGHT key to unlock it. If that doesn't work, the scanner may need to be initialized. Follow the steps in 'Initializing the Scanner to Factory Defaults'.
Why does my Radio Shack Scanner have poor reception?
If your Radio Shack Scanner has poor or no reception, several factors could be responsible. Weak or completely discharged batteries can cause this, so check the batteries or ensure the AC or DC adapter is properly connected. Weak signals might be the issue, so try repositioning the radio. The attenuator might be affecting reception; test performance with and without it activated to find the best setting. Strong signal overload could also be the problem; again, test the attenuator settings. Inspect the antenna and connectors for any issues. Finally, ensure the correct modulation mode is selected for the system you're monitoring.
What to do if my Radio Shack PRO-106 Scanner won’t turn on?
If your Radio Shack Scanner won’t power on, it might not be receiving power. Try recharging the rechargeable batteries or replacing the non-rechargeable batteries. Also, ensure that the adapter’s barrel plug is fully plugged into the DC 9V jack.
Why is my Radio Shack Scanner flashing?
If your Radio Shack Scanner is flashing, it typically indicates that the batteries are low. Recharge the rechargeable batteries or replace the alkaline batteries to resolve this issue.
Why does my Radio Shack Scanner scan slowly?
If your Radio Shack Scanner scans slowly or stops on noise or silence, the SQUELCH control may not be set properly. Set SQUELCH per 'Turning on the Scanner and Setting Squelch' on page 23. Also, the subaudible squelch mode might not be set correctly for conventional objects. Set the correct subaudible squelch mode, refer to 'Appendix B: Detailed Menu Reference: Conv Menu' on page 108.
Why won't my Radio Shack PRO-106 receive digital transmissions?
If your Radio Shack Scanner doesn't receive digital transmissions, the digital channel or talkgroup may not be using APCO-25 digital modulation; the scanner can only receive APCO-25 C4FM/CQPSK IMBE digital signals. Also, the digital channel or talkgroup might be encrypted, and the scanner will not receive encrypted traffic. Finally, the transmission could be from a distant location, so reposition the scanner or use an outdoor antenna to improve reception.
What to do if Radio Shack PRO-106 shows error when uploading from computer?
If you see an error message when trying to upload or download from a computer to your Radio Shack Scanner, and your computer uses Windows XP, it may be missing the necessary USB cable driver. Download and install the file: 'Windows XP Driver to resolve PC connection error' from your scanner’s Product Support page or the Software Download page on www.RadioShack.com. Then make your connection and try again. Be sure the correct COM port is selected in device manager.
General| Brand | Radio Shack |
|---|---|
| Model | PRO-106 |
| Category | Scanner |
| Language | English |
Explains the function of each button and key on the scanner's keypad.
Details the LCD screen, icons, and alphanumeric information displayed.
Lists the key capabilities and technologies of the PRO-106 scanner.
Instructions for attaching the supplied or an external antenna.
Guide on powering the scanner using AA batteries or an external source.
Step-by-step instructions for inserting AA batteries into the scanner.
Procedure to configure battery type for proper detection and charging.
Instructions and notes for recharging rechargeable batteries.
Information on using an external power source for the scanner.
Guidelines for safe earphone and headphone usage to protect hearing.
How to transfer scanner data via cable or USB.
Initial steps for powering on and adjusting squelch.
Controls for scanner sensitivity and interference reduction.
Overview of radio-wide settings adjustable via the Global menu.
Setting a delay to avoid missing replies after transmissions.
Procedure to set the LCD contrast level.
Enabling or disabling the audible beep for key presses.
Configuring keypad and display backlight behavior.
Navigating and interacting with object menus.
Creating and configuring non-trunked AM/FM channels.
Renaming objects for easier identification.
Creating objects to monitor talkgroups on trunked systems.
Defining parameters for trunked radio systems.
Function to copy existing objects for faster entry.
How to start, pause, and resume scanning.
Browsing and selecting objects manually.
Dividing objects into separate lists for easier management.
Adding or removing objects from Scan Lists.
Steps to create a new scannable object.
Editing properties of already created objects.
Assigning custom names to Scan Lists.
Activating or deactivating Scan Lists for scanning.
Enabling/disabling Scan Lists via the Global menu.
List for objects without assigned Scan Lists.
Accessing and managing the Favorites Scan List.
Changing the default Scan List for new objects.
Procedure for removing objects from memory.
Finding objects based on text strings or lockout status.
Displaying objects filtered by their type.
Overview of locking out specific objects from scanning.
Locking out an object until the scanner is turned off.
Locking out an object until it is explicitly unlocked.
Locking out undesired frequencies found during searches.
Locking out undesired talkgroups found via wildcard TGRP.
Parameters for searching a range of frequencies.
Key parameters required for LMIT search.
Searching frequencies optimized for specific radio services.
Key parameters for SRVC search.
Parameters for sweeping frequencies for nearby signals.
Key parameters for STLK object.
Quick access to search modes without saving objects.
Perform limit searches quickly without object setup.
Quick service searches by category without object setup.
Frequency ranges for public safety searches.
Searches frequencies used by railroad communications.
Searches common public safety frequencies.
Searches civilian and military air frequencies.
Searches amateur radio frequencies.
Searches citizen's band radio frequencies.
Searches VHF-FM marine radio bands.
Searches FRS, GMRS, MURS, DOT, STAR frequencies.
Quickly enter any frequency and monitor or search.
Quickly sweep RF spectrum for nearby signals.
Frequency ranges for Signal Stalker II sweeps.
Giving priority to specific objects during scanning.
Enabling/disabling priority for individual objects.
Enabling/disabling priority scan globally.
Scanner samples CONV objects periodically.
Prioritizing TGRPs within a trunked system.
Tracking number of transmissions received per object.
Customizing visual and audible notifications for objects.
Enabling multi-site functionality for trunked systems.
Automating LTR trunking system programming.
Shortcuts for accessing configuration items at power-on.
Setting a password to prevent unauthorized use.
Identifying internal scanner frequencies causing interference.
Compliance information regarding scanning receiver regulations.
Information on legal scanner usage and prohibited listening.
Recommendations for cleaning and maintaining the scanner.
Guidance on seeking assistance for scanner issues.
Technical details including frequency coverage and dimensions.
Detailed list of all frequency ranges the scanner supports.
Information on the scanner's object storage capacity.
Details on V-Scanner storage for configurations.
Overview of preprogrammed dedicated service and limit searches.
Common problems and their solutions.
Procedure to reset global settings without losing programmed data.
Procedure to perform a full factory reset of the scanner.
Comprehensive list of all frequency bands for searching.
Frequency ranges for public safety searches.
Frequency ranges for civilian and military air communications.
Frequency ranges for amateur radio communications.
Comprehensive guide to all scanner menu parameters.
Parameters for global radio-wide settings.
Detailed options for GLOB menu settings.
Advanced settings section within menus.
Parameters for Conventional Channel objects.
Details on settings for CONV objects.
Parameters for Trunking Talkgroup objects.
Details on settings for TGRP objects.
Parameters for Trunking System objects.
Details on settings for TSYS objects.
Parameters for Limit Search objects.
Details on settings for LMIT objects.
Parameters for Service Search objects.
Details on settings for SRVC objects.
Parameters for Signal Stalker II objects.
Details on settings for STLK objects.
Method for entering alphanumeric text and symbols.
Storing and recalling frequently used text phrases.
Index entries starting with the letter A.
Index entries starting with the letter B.
Index entries starting with the letter C.
Index entries starting with the letter D.
Index entries starting with the letter E.
Index entries starting with the letter F.
Index entries starting with the letter G.
Index entries starting with the letter H.
Index entries starting with the letter I.
Index entries starting with the letter K.
Index entries starting with the letter L.
Index entries starting with the letter M.
Index entries starting with the letter N.
Index entries starting with the letter O.
Index entries starting with the letter P.
Index entries starting with the letter Q.
Index entries starting with the letter S.
Index entries starting with the letter T.
Index entries starting with the letter V.
Index entries starting with the letter W.
Contact information for warranty service and support.
