What to do if RADWAG Scales do not switch on?
If your RADWAG Scales don't switch on, it could be due to a discharged battery. Try connecting the scale to the mains to charge the battery. Alternatively, the issue might be due to missing or incorrectly installed batteries. Ensure the batteries are installed correctly, paying attention to the correct polarization.
Why do RADWAG WLC/A2/C/2 Scales switch off automatically?
If your RADWAG Scales are automatically switching off, it's likely due to the parameter being set to a value that enforces shutdown after a specific time. To resolve this, navigate to the 'Othr' menu and set the parameter to 'nonE'.
What to do if my RADWAG WLC/A2/C/2 fail to start?
If your RADWAG Scales fail to start, there are several possible causes: * The power supply may be disconnected. Connect the power supply to the scale. * The battery may be discharged. Connect the power supply to the mains to charge the battery. * There might be no battery installed, or it might be installed incorrectly. Check if the battery is installed correctly, paying attention to the polarization.
Why is there no printout from my RADWAG WLC/A2/C/2 connected printer?
If you are not getting any printouts from your RADWAG Scales connected printer, consider the following: * The printer port might be set incorrectly in the parameter. To fix this, go to the submenu and set the correct parameter value. * The transmission parameters for the selected printer port could be incorrect. Access the menu and adjust the transmission parameters for the selected printer port. * There might be no variable declared in the weighing printout project. Enter the submenu and declare the variables that you want to be printed.
What to do if the displayed mass unit on RADWAG Scales doesn't match the data plate?
If the displayed mass unit on your RADWAG Scales does not comply with the scale data plate, it could be due to: * A changed scale start unit in the parameter. To correct this, enter the submenu and set the unit to comply with the scale data plate. * A changed custom unit in the parameter. To fix this, enter the submenu and set the unit to comply with the scale data plate.
How to fix communication issues with the additional display on RADWAG WLC/A2/C/2?
If you are experiencing communication issues with the additional display on your RADWAG Scales, consider the following: * The additional display port might be set incorrectly in the parameter. To resolve this, enter the < P5.ducE / 5.3.AdSP> submenu and set the correct parameter value. * The transmission parameters for the selected computer port could be incorrect. Enter the menu and set the correct transmission parameters for the selected additional display port.
What to do if RADWAG Scales display 'LH' during start-up?
If your RADWAG Scales display the message 'LH' during start-up, it means the weighing pan was loaded during the start-up. Unload the weighing pan to display zero indication.
Essential safety and operational precautions for using the scale.
Outlines best practices for accurate weighing and scale zeroing.
Covers external, user, and internal adjustment methods.
Describes the adjustment test and how to generate adjustment reports.
Instructions for installing the USB driver for connecting the scale to a computer.
Overview of modes and how to access their specific local settings.
Local settings specific to the weighing mode.
Sets the lower and upper limits for checkweighing.
Explains the process of summing multiple weighings.
Lists common problems, their causes, and solutions for the scale.
Lists and explains common error messages displayed by the scale.
General| Maximum Capacity | 2 kg |
|---|---|
| Display | LCD |
| Interface | RS232 |
| Protection Class | IP 43 |
| Calibration | External |
| Tare Range | -2 kg |
| Stabilization Time | 3 seconds |
| Weighing Pan Dimensions | 128 mm diameter |
| Operating Temperature | 10°C to 30°C |
| Pan Size | 128 mm diameter |
| Calibration Type | External |
| Operating Temperature Range | 10°C to 30°C |
To Next Page
