How to fix missing instrument data on some Raymarine i70 displays?
If instrument or other system data is missing from some, but not all displays, it could be a SeaTalkhs network problem. Check that all required equipment is connected to the SeaTalkhs switch and verify the status of the SeaTalkhs Switch. Also, ensure that SeaTalkhs cables are free from damage.
Why does my Raymarine Marine Equipment display behave erratically?
If your Raymarine Marine Equipment display behaves erratically, consider the following: * Check the fuses and breakers for any intermittent power issues. * Perform a factory reset. Note that this will erase all settings and data stored on the product. It is recommended to save any important data to a memory card before resetting.
What to do if instrument data is unavailable on Raymarine Marine Equipment?
If instrument, engine, or other system data is unavailable at all displays on your Raymarine Marine Equipment, consider the following: * Check the data bus (e.g. SeaTalkng) wiring and connections. * Verify the data source (e.g. instrument display or engine interface) is operating. * If there is a software mismatch between equipment contact Raymarine technical support.
Why is instrument data missing from some Raymarine Marine Equipment displays?
If instrument or other system data is missing from some, but not all, displays on your Raymarine Marine Equipment: * Check that all required equipment is connected to the network. * If there is a software mismatch between equipment contact Raymarine technical support.
Why is instrument data not showing on my Raymarine i70 Monitor display?
If instrument, engine, or other system data is unavailable on all displays, it could be due to several reasons. First, check the data bus wiring and connections to ensure data is being received at the display and verify the overall integrity of the data bus wiring. Also, check the source of the missing data, such as the ST70 instrument or engine interface, and ensure the power to the SeaTalk bus is on. If the data source is not operating, refer to the manufacturer’s handbook for the equipment in question.
What to do if my Raymarine i70 Monitor display is behaving erratically?
If your Raymarine Monitor display is behaving erratically with frequent unexpected resets or system crashes, there are a few things you can check. Start by checking the relevant fuses and breakers, and ensure the power supply cable is sound, with tight, corrosion-free connections. Also, verify the power source provides the correct voltage and sufficient current. Make sure the front bezel is fitted correctly and all buttons operate freely. As a last resort, perform a factory reset via Menu > System Setup > Settings and Data Reset.
How to troubleshoot a Raymarine Monitor that won't start?
If your Raymarine Monitor system or part of it does not start, begin by checking the relevant fuses and breakers. Then, inspect the power supply cable to ensure it is in good condition and that all connections are tight and free from corrosion. Finally, confirm that the power source provides the correct voltage and sufficient current.
What to do if Raymarine Monitor display behaves erratically?
If your Raymarine Monitor display behaves erratically with frequent unexpected resets, system crashes, or other erratic behavior, begin by checking the relevant fuses and breakers. Ensure the power supply cable is in good condition and that all connections are tight and free from corrosion. Verify that the power source provides the correct voltage and sufficient current. If these steps don't resolve the issue, it could be due to a software mismatch, requiring an upgrade. In that case, visit www.raymarine.com and click on support for the latest software downloads. As a last resort, perform a factory reset, but remember that this will erase all settings and data stored on the product; therefore, save any important data to a memory card before resetting.
What to do if Raymarine i70 Monitor will not start up (restart loop)?
If your Raymarine Monitor will not start up and is stuck in a restart loop, refer to the solutions for the issue 'Product does not turn on or keeps turning off'. If that doesn't resolve the problem, the product's software might be corrupted. Try downloading and installing the latest software from the Raymarine website. As a last resort for display products, attempt a 'Power on Reset'. Keep in mind that this will delete all settings, presets, and user data, reverting the unit to factory defaults.
Why is instrument, engine or other system data unavailable at all Raymarine Monitor displays?
If instrument, engine, or other system data is unavailable at all displays on your Raymarine system, check the data bus (e.g., SeaTalk ng) wiring and connections to ensure they are properly connected. Verify the overall integrity of the data bus wiring. Check the source of the missing data, such as the instrument display or engine interface, and ensure it is operating correctly. Also, check the power to the SeaTalk bus. If a software mismatch between equipment is suspected, contact Raymarine technical support.
General| Display Type | LCD |
|---|---|
| Resolution | 320 x 240 pixels |
| Waterproof Rating | IPX6 |
| Interface | SeaTalkng / NMEA 2000 |
| Weight | 0.3 kg |
| Display Size | 4.1 inches |
| Backlighting | LED |
| Power Supply | 12V DC |
To Next Page