How to fix missing instrument data on some Raymarine i70 displays?
If instrument or other system data is missing from some, but not all displays, it could be a SeaTalkhs network problem. Check that all required equipment is connected to the SeaTalkhs switch and verify the status of the SeaTalkhs Switch. Also, ensure that SeaTalkhs cables are free from damage.
Why does my Raymarine Marine Equipment display behave erratically?
If your Raymarine Marine Equipment display behaves erratically, consider the following: * Check the fuses and breakers for any intermittent power issues. * Perform a factory reset. Note that this will erase all settings and data stored on the product. It is recommended to save any important data to a memory card before resetting.
What to do if instrument data is unavailable on Raymarine Marine Equipment?
If instrument, engine, or other system data is unavailable at all displays on your Raymarine Marine Equipment, consider the following: * Check the data bus (e.g. SeaTalkng) wiring and connections. * Verify the data source (e.g. instrument display or engine interface) is operating. * If there is a software mismatch between equipment contact Raymarine technical support.
Why is instrument data missing from some Raymarine Marine Equipment displays?
If instrument or other system data is missing from some, but not all, displays on your Raymarine Marine Equipment: * Check that all required equipment is connected to the network. * If there is a software mismatch between equipment contact Raymarine technical support.
Why is instrument data not showing on my Raymarine i70 Monitor display?
If instrument, engine, or other system data is unavailable on all displays, it could be due to several reasons. First, check the data bus wiring and connections to ensure data is being received at the display and verify the overall integrity of the data bus wiring. Also, check the source of the missing data, such as the ST70 instrument or engine interface, and ensure the power to the SeaTalk bus is on. If the data source is not operating, refer to the manufacturer’s handbook for the equipment in question.
What to do if my Raymarine i70 Monitor display is behaving erratically?
If your Raymarine Monitor display is behaving erratically with frequent unexpected resets or system crashes, there are a few things you can check. Start by checking the relevant fuses and breakers, and ensure the power supply cable is sound, with tight, corrosion-free connections. Also, verify the power source provides the correct voltage and sufficient current. Make sure the front bezel is fitted correctly and all buttons operate freely. As a last resort, perform a factory reset via Menu > System Setup > Settings and Data Reset.
How to troubleshoot a Raymarine Monitor that won't start?
If your Raymarine Monitor system or part of it does not start, begin by checking the relevant fuses and breakers. Then, inspect the power supply cable to ensure it is in good condition and that all connections are tight and free from corrosion. Finally, confirm that the power source provides the correct voltage and sufficient current.
What to do if Raymarine Monitor display behaves erratically?
If your Raymarine Monitor display behaves erratically with frequent unexpected resets, system crashes, or other erratic behavior, begin by checking the relevant fuses and breakers. Ensure the power supply cable is in good condition and that all connections are tight and free from corrosion. Verify that the power source provides the correct voltage and sufficient current. If these steps don't resolve the issue, it could be due to a software mismatch, requiring an upgrade. In that case, visit www.raymarine.com and click on support for the latest software downloads. As a last resort, perform a factory reset, but remember that this will erase all settings and data stored on the product; therefore, save any important data to a memory card before resetting.
What to do if Raymarine i70 Monitor will not start up (restart loop)?
If your Raymarine Monitor will not start up and is stuck in a restart loop, refer to the solutions for the issue 'Product does not turn on or keeps turning off'. If that doesn't resolve the problem, the product's software might be corrupted. Try downloading and installing the latest software from the Raymarine website. As a last resort for display products, attempt a 'Power on Reset'. Keep in mind that this will delete all settings, presets, and user data, reverting the unit to factory defaults.
Why is instrument, engine or other system data unavailable at all Raymarine Monitor displays?
If instrument, engine, or other system data is unavailable at all displays on your Raymarine system, check the data bus (e.g., SeaTalk ng) wiring and connections to ensure they are properly connected. Verify the overall integrity of the data bus wiring. Check the source of the missing data, such as the instrument display or engine interface, and ensure it is operating correctly. Also, check the power to the SeaTalk bus. If a software mismatch between equipment is suspected, contact Raymarine technical support.
General| Display Type | LCD |
|---|---|
| Resolution | 320 x 240 pixels |
| Waterproof Rating | IPX6 |
| Interface | SeaTalkng / NMEA 2000 |
| Weight | 0.3 kg |
| Display Size | 4.1 inches |
| Backlighting | LED |
| Power Supply | 12V DC |
Includes warnings about sun covers, water ingress, and product disposal advice.
Covers Raymarine's disclaimers, declaration of conformity, and product usage scope (IMO/SOLAS).
Details warranty registration process and a statement on the technical accuracy of the manual.
Information on available manuals, ordering printed copies, and document conventions.
Specifies the software version this document applies to and lists compatible products.
Explains button functions, powering the display on/off, and battery considerations.
Guides through language, boat type selection, and welcome message for first-time setup.
Details how to adjust the display's brightness level.
Explains how to synchronize brightness across multiple displays via network groups.
Covers changing display color schemes and setting display response times.
Explains how to select preferred data sources for various parameters.
Details the dynamic Quick Options menu and the process for updating product software.
Covers setting depth offset and various methods for speed calibration.
Details calibrating wind transducers, including alignment and apparent wind speed adjustment.
Covers centering the rudder, adjusting rudder angle, and swinging the compass.
Explains the concept of favorite pages, default setup, and customization limits.
Describes various pre-defined favorite page types like Heading & Speed, Digital Depth, and Engine pages.
Details options for editing, adding, deleting pages, and managing page order and rollover.
Guides on editing existing pages, adding new pages, and managing page lock features.
Lists data items for favorite pages and quick view, in digital, dial, and graphical formats.
Explains AIS functionality, how it works, and the meaning of different target symbols.
Covers setting AIS range, viewing target details, and managing silent mode.
Guides on setting up fuel manager, logging fuel, and detecting fuel messages.
Details choosing calculation methods and displaying fuel estimates on favorite pages.
Explains how to reset fuel usage for the season or current trip.
Details how to set up countdown timers and use the race timer functionality.
Covers various alarms (anchor, depth, speed, MOB) and how to handle them.
Guides on setting thresholds for depth, speed, temperature, wind, and other alarms.
Guides on setting up and calibrating various transducers (Depth, Speed, Wind, Rudder, Compass).
Covers date, time, units, language, boat type, variation, network groups, and data sources.
Provides solutions for common problems, including power-up issues and data reception problems.
Addresses erratic behavior, system crashes, and the procedure for performing a factory reset.
Provides contact information for Raymarine support and explains how to view product details.
To Next Page