Raymarine E-Series - User Manual

Other manuals for Raymarine E-Series

Installation Manual54 pages

Reference Manual360 pages

Installation Instructions112 pages

Operating Guide18 pages

Brochure112 pages

Questions and Answers

C
Colleen McleanAug 18, 2025
How to troubleshoot a 'No depth reading / lost bottom lock' on Raymarine Marine Equipment?
- L
  lucas79Aug 18, 2025
  If your Raymarine Marine Equipment is not showing a depth reading or has lost bottom lock, verify that the transducer has been installed according to its instructions. If the transducer angle is too great, adjust it, as the beam may be missing the bottom. If the transducer has a kick-up mechanism, ensure it hasn't been activated by hitting an object. Check the power supply voltage as close to the unit as possible under load. Inspect the transducer for damage and ensure it is free from debris or fouling.
A
Amber DavisAug 21, 2025
What causes a 'No Data' or 'No scanner message' on Raymarine Marine Equipment?
- K
  Kelly BrownAug 21, 2025
  If your Raymarine Marine Equipment displays 'No Data' or 'No scanner message', verify that the scanner power supply cable is in good condition and that all connections are secure and free from corrosion. Also, check the relevant fuses and breakers. Ensure the power source provides the correct voltage and sufficient current, using a voltage booster if needed.
J
Justin GrahamAug 23, 2025
What to do if Raymarine Marine Equipment radar will not initialize (Voltage control module (VCM) stuck in “sleep mode”)?
- L
  Lauren FullerAug 23, 2025
  If your Raymarine Marine Equipment radar will not initialize, and the Voltage Control Module (VCM) is stuck in 'sleep mode', check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V. A poor power connection may be the cause.
E
eileen64Aug 26, 2025
How to fix an incorrect speed reading (from DST transducer) on Raymarine Marine Equipment?
- J
  Jacob ParkerAug 26, 2025
  To correct an incorrect speed reading from a DST transducer on your Raymarine Marine Equipment, start by checking that the paddle wheel is clean. If that doesn't solve the issue, add a speed offset. If no speed is displayed, ensure the transducer has a speed element or select a transducer that supports speed measurement from the Transducer Set-Up menu.
J
jessica22Sep 1, 2025
What to do if my Raymarine Marine Equipment will not boot up (re-boot loop)?
- B
  bblanchardSep 1, 2025
  If your Raymarine Marine Equipment product won't boot up or is stuck in a reboot loop, review the solutions for a product that doesn't turn on or keeps turning off. If the problem persists, it could be due to software corruption. Try re-flashing the latest software from the Raymarine website. As a last resort on display products, perform a 'Power on Reset'; however, this will erase all settings, presets, and user data, reverting the unit to factory defaults.
Y
ydanielSep 3, 2025
Why does my Raymarine Marine Equipment show a “No Fix” GPS status icon?
- D
  davidcohenSep 3, 2025
  If your Raymarine Marine Equipment displays a 'No Fix' GPS status icon, it could be due to your geographic location or current conditions preventing a satellite fix. Check again later under better conditions or in a different location. Ensure that external GPS connections and cabling are correct and fault-free. Make sure the GPS antenna has a clear view of the sky. Refer to the installation instructions for any GPS installation issues.
B
Brandy AyersSep 6, 2025
Why is the boat symbol a solid circle on my Raymarine E-Series?
- J
  Jaime MccoySep 6, 2025
  If the Raymarine Monitor boat symbol is drawn as a solid circle, this indicates that no heading or Course Over Ground (COG) data is available to the system.
S
Samuel StewartSep 8, 2025
Why is the 'FIND SHIP' soft key greyed out on my Raymarine E-Series Monitor?
- D
  daviswilliamSep 8, 2025
  If the FIND SHIP soft key is greyed out on your Raymarine Monitor, it is because the system does not have a position fix.
P
Paula SmithSep 12, 2025
Why is the boat symbol not displayed on my Raymarine E-Series?
- L
  llaneSep 12, 2025
  If the boat symbol is not displayed on your Raymarine Monitor, it's likely due to the system not having a position fix.
F
frederickgarciaSep 12, 2025
What to do if the weather map on my Raymarine E-Series doesn't redraw during use?
- K
  Kelly MccannSep 13, 2025
  If, during use, the weather map stays in the last view and does not redraw on your Raymarine Monitor, ensure that the FIND SHIP function is activated and that motion mode is not active.