How to troubleshoot a blank display on Raymarine Marine Equipment?
If you are experiencing a blank display on your Raymarine marine equipment, check the fuse or circuit breaker. Also, check the power supply and the SeaTalk cabling and connector security.
Why won't my Raymarine Marine Equipment system start up?
If your Raymarine marine equipment system or part of it does not start up, it may be due to a power supply problem. Check the relevant fuses and breakers. Also, ensure the power supply cable is in good condition, with tight, corrosion-free connections. Verify that the power source provides the correct voltage and sufficient current.
What to do if my Raymarine Marine Equipment display is behaving erratically?
If your Raymarine marine equipment display behaves erratically, with frequent unexpected resets, system crashes, or other erratic behavior, it could be due to an intermittent power issue. Check the fuses and breakers. Also, check the power supply cable for damage and ensure all connections are tight and free of corrosion. Confirm the power source provides the correct voltage and current. Another potential cause is a software mismatch, which may require an upgrade from the Raymarine website. A factory reset may also resolve the issue, but remember that this will erase all settings and data stored on the product.
How to fix SeaTalk information transfer issues in Raymarine Marine Equipment?
If SeaTalk information is not being transferred between Raymarine marine equipment instruments, check the security of SeaTalk connections between the units. Also, check the condition of the SeaTalk cables. To identify a faulty unit, disconnect the units one by one.
What to do if a group of SeaTalk units in my Raymarine Marine Equipment system is not working?
If a group of SeaTalk units in your Raymarine marine equipment system is not working, start by checking the security of the SeaTalk connectors between the functioning and non-functioning units. Then, inspect the condition of the SeaTalk cable between these units.
Why is there no speed information on my Raymarine Marine Equipment but water temperature is present?
If there is no speed information on your Raymarine marine equipment, but the water temperature is present, the transducer paddle wheel may be fouled. If you need to remove the transducer insert, have the transducer bung to hand and secure it in the transducer body immediately after the insert is removed, to prevent excessive ingress of water.
What to do if there is no data on my Raymarine Marine Equipment?
If there is no data on your Raymarine marine equipment, check the condition of the transducer cable and ensure the connections are secure. Also, check the condition of the transducer face and remove any debris. For i40 wind, if true wind speed information is missing but apparent wind is present, this could be due to no speed information via SeaTalk.
Why does the depth reading flash when underway on my Raymarine Marine Equipment?
If the depth reading flashes when underway on your Raymarine marine equipment, ensure the reading stabilizes when clear of disturbed water such as vessel wakes or propeller wash.
What to do if Raymarine Marine Equipment shows low battery?
Recharge your vessel's battery as soon as possible if you have low battery on your Raymarine marine equipment.
Product must be installed and operated per instructions to avoid injury, damage, or poor performance.
Product not approved for hazardous/flammable atmospheres. Do NOT install near fuel tanks or in engine rooms.
Do not connect this unit to a system with positive grounding.
Ensure power source is protected by a suitably-rated fuse or circuit breaker.
Ensure vessel's power supply is OFF before starting installation. Do NOT connect/disconnect with power on.
Product contains high voltage. Servicing requires specialized procedures by qualified technicians. No user-serviceable parts.
Do NOT cut, shorten, or splice transducer cable. Do NOT remove connector. Cutting voids warranty.
Contains no user serviceable components. Refer all maintenance/repair to authorized dealers. Unauthorized repair may affect warranty.
Instructions for safe cleaning of the unit, including what to avoid.
Provides a step-by-step checklist for planning and executing the installation of the instrument.
Guidance on choosing an optimal location for the display unit, considering ventilation, mounting, and interference.
Criteria for selecting the best location for speed and depth transducers on the vessel.
Details how to connect the unit to a 12 V dc power supply, either directly or via the SeaTalk network.
Overview of the operational capabilities of the i40 Bidata instrument, including speed, log, trip, and temperature data.
Detailed steps for user calibration, including setting display response, units, and offsets.
Details the functions of the i40 Depth instrument, providing depth information and alarm settings.
Steps for user calibration, including depth response, units, and depth offset settings.
Steps for user calibration, including speed response, units, distance, temperature, and calibration factor.
Steps for user calibration, including wind angle/speed response, units, linearization, and alignment.
Details available alarms (depth, anchor, wind), how they are indicated, and how to silence, enable/disable, and set thresholds.
Provides guidance on diagnosing and correcting common problems with marine electronics installations.
Lists common instrument problems (low battery, blank display, no data) with causes, screenshots, and solutions.
Addresses problems related to the system not starting up, focusing on power supply issues.
Covers issues like erratic display behavior, resets, crashes, and software mismatches.
General| Display Type | LCD |
|---|---|
| Backlighting | Yes |
| Power Supply | 12V DC |
| Power Consumption | 2.4W |
| Waterproof Rating | IPX6 |
| Dimensions | 128 x 72 x 45 mm |
| Interface | SeaTalk |
| Operating Temperature | -10°C to +55°C |
| Weight | 0.3 kg |
To Next Page
