How to adjust brightness on Raymarine eS Monitor?
If the image on your Raymarine monitor is too dark or too light, the cause may be: * **Display brightness is set too low**: Use the brightness controls at the display to adjust accordingly.
What to do if the Raymarine eS Monitor displays a “No Fix” GPS status icon?
If your Raymarine monitor displays a “No Fix” GPS status icon, it could be due to: * **Geographic location or prevailing conditions**: Check periodically to see if a fix is obtained in better conditions or another geographic location. * **GPS connection fault**: Ensure that external GPS connections and cabling are correct and fault free. * **External GPS antenna in poor position**: Ensure the GPS antenna has a clear view of the sky.
Why my Raymarine eS Monitor will not boot up (re-boot loop)?
If your Raymarine monitor product will not boot up and is stuck in a re-boot loop, the issue may be due to: * **Power supply and connection**: Refer to the solutions for 'Product does not turn on or keeps turning off'. * **Software corruption**: Try re-flashing the latest software from the Raymarine website. As a last resort, perform a ‘Power on Reset’; be aware that this will delete all settings, presets, and user data, reverting the unit to factory defaults.
What causes a 'No Data' or 'No scanner' message on Raymarine Monitor?
If your Raymarine monitor displays no data or a 'No scanner' message, check the following: * **Radar scanner power supply**: Ensure the scanner power supply cable is in good condition and that all connections are tight and free from corrosion. * **SeaTalkhs / RayNet network**: Verify the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler. * **Switch at scanner pedestal**: Ensure the scanner pedestal switch is in the ON position.
Why is video not displayed on my Raymarine eS?
If the video is not displayed on your Raymarine monitor, consider these potential causes: * **Camera is in Standby mode**: Use the camera controls (either the thermal camera application or JCU) to “wake” the camera from standby. * **Problem with the thermal camera video connections**: Check thermal camera video cables are sound and properly connected. Ensure that the video is connected into video input 1 at the multifunction display or GVM. Ensure that the correct video input is selected at the display. * **Problem with power supply to the camera or JCU**: Check the power connections to the camera and JCU / PoE injector (if used). Ensure that the power switch / breaker is on. Check the fuse / breaker state.
What to do if Raymarine eS radar will not initialize?
If the radar on your Raymarine monitor will not initialize (Voltage control module (VCM) stuck in “sleep mode”), the cause may be: * **Intermittent or poor power connection**: Check power connection at VCM. (Voltage at input = 12 / 24 V, Voltage at output = 40 V)
How to fix incorrect radar bearing on Raymarine eS?
If the bearing of a target on the radar screen of your Raymarine monitor is incorrect, the cause may be: * **The radar bearing alignment requires correcting**: Check and adjust radar bearing alignment.
What causes erratic controls on Raymarine eS?
If you are experiencing erratic or unresponsive controls on your Raymarine monitor, it could be due to: * **Network problem**: Check that the controller and thermal camera are correctly connected to the network. Note: This may be a direct connection or via a Raymarine network switch.
Why can't I control thermal camera from Raymarine Monitor?
If you cannot control the thermal camera from your Raymarine display or keyboard, it might be because: * **Thermal camera application is not running**: Ensure the thermal camera application is running on the multifunction display (as opposed to the video application which does not have camera controls).
Why is Raymarine eS showing incorrect speed reading?
If you're getting an incorrect speed reading from the DST transducer on your Raymarine monitor, check the following: * **Paddle wheel fault**: Check that the paddle wheel is clean. * **No speed offset set**: Add speed offset. * **Transducer does not have a speed element**: Install transducer with speed element to enable speed readings. * **Incorrect transducer selected**: Select a transducer that supports speed measurement from the Transducer Set-Up menu.
Covers potential ignition, high voltages, grounding, and operational safety.
Outlines the key tasks required for a successful installation.
Provides guidance on choosing a suitable location considering various factors.
Details 3-pin and combined power/data cable connections and ratings.
Explains SeaTalkng, NMEA 2000, SeaTalk, and NMEA 0183 connections.
Details how to connect sonar modules and radar scanners to the system.
Provides instructions for mounting the display directly onto a flat surface.
Instructions for powering the unit on/off and using its physical controls.
Guides through essential initial configuration settings and procedures.
Verifies the correct operation of the GPS receiver using the chart application.
Guides on checking radar scanner operation, including safety precautions.
Addresses issues with the unit not turning on or rebooting.
Contact information and resources for obtaining customer and technical support.
To Next Page
General
