G
George MontgomerySep 6, 2025
What to do if the extension cord is too long on Record Power Lathe?
- Mmatthew53Sep 6, 2025
Reduce the length of the extension cord.
To Next PageTo Next PageWhat to do if the extension cord is too long on Record Power Lathe?
Reduce the length of the extension cord.
What to do if my Record Power Lathe spindle stalls?
If the spindle on your Record Power Lathe stalls or won't turn, the issue could stem from several causes. It might be due to an excessive depth of cut, in which case you should reduce the cutting depth. Alternatively, a loose or broken belt could be the culprit, requiring you to adjust the belt tension or replace the drive belt. Worn spindle bearings can also cause this issue, necessitating bearing replacement. Finally, check if the indexing lock is engaged; if so, disengage it and inspect the spindle pulley for any damage, replacing it if needed.
Why does my Record Power Lathe motor overheat?
Your Record Power Lathe motor may overheat because it's overloaded, so you should reduce the load on the motor. Another possible cause is insufficient cooling, so you should clean the motor to increase airflow or reduce how long you use it.
What to do if turning tool digs into timber on Record Power Lathe?
If your turning tool digs into the timber or grabs it when using your Record Power Lathe, there are several potential reasons. The turning tool might be blunt, requiring you to sharpen it. The tool rest could be set too low, so adjust it to the correct height. It's also possible that the tool rest is too far from the timber, so move it closer. Finally, ensure you are using the correct turning tool for the job.
Why is my Record Power Lathe making excessive motor noise?
Excessive motor noise in your Record Power Lathe can be attributed to a couple of reasons. It could be a faulty motor, which would require replacement. Alternatively, the pulley blind set screws might be loose, and you would need to tighten them.
What to do if my Record Power DML320 Lathe has low voltage?
If you are experiencing low voltage with your lathe, check the power supply to the machine and all external connections. Also, decrease the load on the circuit, reduce the length of the wire or use a suitable diameter of cable, and consider having a qualified electrician install a properly sized circuit breaker.
Why does the tailstock on my Record Power DML320 Lathe move when applying pressure?
If the tailstock moves when applying pressure, it could be due to: * Excessive pressure being applied by the tailstock to the workpiece: Apply only sufficient force with the tailstock to hold the timber securely between centres. * The tailstock not being secured in place: Tighten the tailstock locking lever. * Dirty lathe bed and tailstock mating surfaces: Remove and clean the tailstock and lathe bed.
What to do if my Record Power DML320 Lathe is not plugged in?
Plug the machine in.
What to do if Record Power DML320 Lathe circuit breaker does not have sufficient capacity?
Have a qualified electrician install proper sized circuit breaker.
What to do if Record Power DML320 circuit is overloaded?
Decrease the load on the circuit.
General| Brand | Record Power |
|---|---|
| Model | DML320 |
| Category | Lathe |
| Language | English |
Essential safety gear like eyewear, gloves, and respiratory protection to prevent injury.
Proper dressing, securing workpieces, avoiding overreaching, and safe movement of the machine.
Proper connections, use of extension cables, and preventing electric shock.
The importance of dust extraction for health, safety, and machine performance.
Specific safety measures for woodturning, including familiarisation and workpiece mounting.
Procedure for adjusting the drive belt to select different speed ranges.
Starting, stopping, speed adjustment, direction control, and handling stalls.
Correct positioning of tool rests and techniques for using roughing and spindle gouges.
Essential role of dust extraction for user health, safety, and machine maintenance.
Solutions for common problems like machine not starting or stalling.
Diagnosing and resolving issues related to motor overheating or spindle not turning.
