Reese Carry Power TransRACK

Need help?

Do you have a question about the Reese Carry Power TransRACK and is the answer not in the manual?

Summary

CAUTION!

Product Use and Safety Warnings

Read and follow all warnings and instructions before using this product to prevent damage or injury.

WARNING!

Load Capacity and Vehicle Handling

Do not exceed 800 lbs capacity or vehicle limits; loads affect center of gravity and handling.

Product Integrity and Modifications

Avoid modifications; unintended use voids warranty and creates hazardous conditions.

IMPORTANT!

Load Security and Regulations

Secure loads per local regulations, check connections, and distribute loads evenly.

Vehicle Compatibility and Maintenance

Consult vehicle manual for ratings; lubricate hardware; some vehicles need reinforcing kits.

Fit Up

Bed Liner and Vehicle Design

Designed for trucks without over-rail liners; trimming may be needed for under-rail liners.

Product Assembly

Vertical Support Assembly Steps

Assemble the four vertical supports using provided parts and following sequential steps.

Horizontal Load Bar Assembly Steps

Assemble the horizontal load bars by connecting sections and attaching knobs and caps.

Vehicle Installation

Mounting Vertical Supports

Choose locations and attach the assembled vertical supports to the truck bed rails.

Installing Cross Bars

Place cross bars onto vertical supports and secure them using knobs.

Assembly and Installation of Load Stops

Load Stop Assembly

Assemble the load stop components by connecting the triangle piece to the clamp.

Load Stop Installation

Attach load stops to the load bars using carriage bolts and knobs for securing cargo.

Load Stop Usage and Permanent Mounting

Cargo Securing with Load Stops

Position load stops to secure rectangular or semi-circular loads and use tie-downs.

Permanent Mounting Procedure

Permanently mount the rack by drilling holes in the truck bed and securing with bolts and nuts.

Maintenance and Hardware Recommendations

Inspect rack regularly, check tightness, use polish for appearance, and consider hardware upgrades.

REESE TwoYear Limited Warranty

Warranty Coverage and Duration

Product is warranted against material/workmanship defects for two years from retail purchase.

Warranty Limitations and Exclusions

Excludes normal wear, finish damage, abuse, misuse, improper installation, or alterations.

Purchaser Obligations and Legal Rights

Requires proof of purchase for claims; warranty grants specific legal rights varying by state.

Remedy Limits and Consequential Damages

Exclusive remedy is replacement/refund; excludes incidental/consequential damages.

The Reese TransRACK Cargo Truck Rack (Product No. 70547) is a robust and versatile accessory designed for transporting various items on pick-up trucks. This rack system is engineered to provide a secure and adjustable solution for carrying ladders, lumber, pipe, and recreational items such as canoes and kayaks.

Function Description:

The TransRACK system consists of two horizontal load bars supported by four vertical supports, which are clamped onto the truck bed rails. Its primary function is to extend the cargo-carrying capacity of a pick-up truck, allowing users to transport longer and bulkier items that would not fit within the truck bed alone. The design emphasizes adjustability to accommodate different truck sizes and cargo types. The rack can be installed with or without permanent mounting, offering flexibility to users. Load stops are included to help secure cargo on the horizontal bars, preventing shifting during transit. The system is designed for easy installation without the need for drilling in most cases, utilizing a clamping mechanism.

Important Technical Specifications:

Load Capacity: The TransRACK has a maximum load capacity of 800 lbs., provided the load is evenly distributed. "Distributed load" is defined as a load that is not concentrated in a small area. Users are cautioned not to exceed this limit or the vehicle manufacturer's specified load capacity for rail-mounted accessories, whichever is less.
Materials: The rack is constructed from lightweight aluminum extrusion, which contributes to its overall strength and corrosion resistance. Stainless steel hardware is used for connections, ensuring durability and long-term performance, especially when lubricated with an anti-seize lubricant.
Finish: The rack features a wear-resistant natural finish, which helps maintain its appearance over time.
Design: It incorporates an aerodynamic design, which can help reduce wind resistance and noise during travel.
Anchor Points: The system includes "Double Lock" anchor points, enhancing the security of the rack to the truck bed.
Adjustability: The rack is fully adjustable to fit various pick-up truck models and bed lengths.
Installation: Designed for "easy-on bar clamps" and "no-drill installation" for most applications. However, optional permanent mounting is available, requiring drilling into the truck bed rails.
Hardware: Key hardware components include 3/8-16 x 2" long square neck bolts, 3/8-16 hex nuts, 3/8" lock washers, 1/4-20 set screws, and 3/8-16 x 1" long square neck bolts with knobs for securing load bars and load stops.

Usage Features:

Versatile Cargo Transport: Ideal for ladders, lumber, pipe, canoes, kayaks, and other similar materials.
Adjustable Fit: The fully adjustable nature ensures compatibility with a wide range of pick-up trucks, allowing users to customize the rack's position to suit their specific vehicle and cargo needs.
Load Stops: Included load stops can be positioned anywhere along the cross bars. They can be oriented with flat sides facing each other for rectangular loads or angled sides for semi-circular loads, providing flexibility in securing different cargo shapes. Users are reminded that load stops alone are not sufficient to secure a load, and tie-downs must always be used.
Easy Installation: The primary installation method involves clamping the vertical supports to the truck bed rails, which typically does not require drilling. This allows for relatively quick setup and removal.
Optional Permanent Mounting: For users who desire a more secure or long-term installation, the rack can be permanently mounted to the truck bed rails using bolts, washers, and nuts, requiring drilling.
Aerodynamic Design: The rack's aerodynamic profile is intended to minimize wind resistance and potential noise, contributing to a smoother driving experience.
Compatibility with Bed Liners: The TransRACK is designed for trucks without traditional over-the-rail plastic bed liners but can be installed on trucks with under-the-rail bed liners with minimal trimming. Spray-on bed liners will not interfere with the product.

Maintenance Features:

Regular Inspection: Users are advised to inspect the entire rack often for any signs of damage, such as bends, creases, cracks, or breaks. Discontinue use if damage is observed.
Tightness Check: All connections should be checked periodically for tightness, especially after driving, to ensure cargo security and rack stability.
Appearance Maintenance: Occasional use of an aluminum polish is suggested if a brighter appearance is desired.
Hardware Lubrication: Lubricating stainless steel hardware with an anti-seize lubricant is recommended for best long-term performance.
Thread Locker: If the rack will not be moved or removed frequently, using a thread locker on connecting hardware may be beneficial for enhanced security.
Hardware Replacement Options: For better clearance or security, the 3/8-16 eyebolts for the mounting clamps can be replaced with 3/8-16 x 3.50 long hex bolts or socket head cap screws. The blue knobs can also be replaced with 3/8-16 hex nuts.

Important Safety Warnings:

Exceeding the load capacity or vehicle GVW rating can severely alter vehicle handling, braking, and stability, potentially leading to damage, injury, or rollover.
Loads carried above bed rails increase the truck's center of gravity. Avoid sharp turns and excessive speeds.
Always secure long loads to the front and rear of the vehicle.
Improperly secured ladders can cause damage to the ladder and lead to structural collapse.
Do not use the rack in truck beds with excessive rust, as this may decrease capacity and lead to product or bed failure.
Any modification or unintended use of the product voids the warranty and can create hazardous conditions.
Loads must comply with local height and identification regulations.
The tailgate should be in the up position for better truck bed stabilization when using the rack.
Some vehicle manufacturers may require a reinforcing kit; users should contact their dealership for details.

The Reese TransRACK is a reliable and adaptable solution for expanding a pick-up truck's cargo capabilities, designed with user convenience, safety, and durability in mind.