REHM TIG.STAR 170 DC - User Manual

To Next Page

OPERATING INSTRUCTIONS

TIG inert gas welding equipment

TIGER DIGITAL 230 DC / AC/DC ULTRA/HIGH

TIGER DIGITAL 180 DC / AC/DC ULTRA/HIGH

TIG.STAR 170 DC / AC/DC

Main Page

Product Identification2
Table of Contents3
Introduction6
Foreword6
General Description7
Principle of the TIG Inert Gas Welding Process8
Scope of Application of TIG Welding Equipment8
Intended Use8
Symbols Used9
Safety Information10
Warning Symbols in These Operating Instructions10
Warning Symbols on the System10
Notes and Requirements11
Unit Description13
Function Description15
Overview of the Operating Panel15
Operation Description16
Controls16
Operating Functions17
Switch on21
Peculiarities of the Operating Panel21
Corner Menu Functions22
Corner Menu Welding Processes (Top Left)22
Electrode Welding22
Electrode BOOSTER Function22
Corner Menu Operating Mode (Top Right)23
Cycle Operating Mode23
Cycle Operating Mode24
TIG Spot Welding24
TIG Interval25
High-Frequency (HF) Ignition26
Welding with HF Ignition26
Welding Without HF Ignition27
Corner Menu Welding Process (Bottom Right)28
Time Pulses28
Hyper Pulses28
Corner Menu Polarity (Bottom Left)29
Alternating Current (~)29
Dual Wave29
DC Positive Positive Pole (+)29
DC Negative Pole30
Parameter Settings31
Setting the TIG Welding Parameters31
Gas Pre-Flow Time31
Ignition Power31
Starting Current32
Slope-Up Time32
And Pulse Time T32
Automatic Pulsing33
Manual Pulsing34
Slope-Down Time34
End Crater Current L34
Gas Post Flow Time35
AC Settings Menu36
AC Waveform36
AC Frequency (Hz)36
AC Balance ( )36
Further Settings for Dualwave36
Menu Spot Welding and Interval37
Spot Time37
Pause Time37
Electrode Welding Parameters37
Setting Options (from Left to Right)38
Hotstart38
Welding Current I138
Arcforce38
Anti-Stick-Automatic39
Submenus40
Language Menu40
Assist40
Save and Load Programs42
Quick Program Buttons P142
Memory Programs 5 to 9942
Manage Parameter Lists (Folders)43
Optional Water Cooling Unit45
Setup / Special Parameters46
Error Memory50
Indicating Symbol50
Accessories51
Foot-Actuated Remote Controller TIGER DIGITAL 180/23051
REHM TIG Torch51
Optional Water Cooling Unit51
Commissioning52
Safety Information52
Working under Increased Electrical Hazard (IEC 874, en 60974-1, TRBS 2131 and BGR 500 KAP. 2.26)52
Placement and Transportation of the Welding Unit53
Connecting the Welding Unit53
Cooling the Welding Unit53
Guidelines for Working with Welding Current Sources54
Connecting the Welding Leads and the Torch54
Connection of External Components54
Operation55
Safety Information55
Electrical Hazard55
Instructions for Your Personal Safety55
Fire Protection56
Ventilation56
Checks before Switching on57
Connecting the Grounding Cable57
Practical Instructions for Use57
Faults TIG Welding Unit60
Safety Information60
Table of Faults60
Error Messages63
Maintenance Work65
Safety Information65
Maintenance Table65
Cleaning the Inside of the Unit66
Proper Disposal66
Technical Data67
Accessories71
Circuit Diagrams73
Index79

Need help?

Do you have a question about the REHM TIG.STAR 170 DC and is the answer not in the manual?

REHM TIG.STAR 170 DC Specifications

General

Brand	REHM
Model	TIG.STAR 170 DC
Category	Welding System
Language	English

Related product manuals

REHM SYNERGIC.PRO2 170-2

62 pages

REHM TIGER 210 AC/DC

64 pages

REHM TIGER 180 AC/DC HIGH

68 pages

TIGER DIGITAL 230 AC/DC ULTRA

83 pages

INVERTIG.PRO digital 240 DC, 240 AC/DC

88 pages

REHM INVERTIG i 260 DC

92 pages

REHM SYNERGIC.ARC 251

84 pages

REHM BARRACUDA RTC 60

55 pages

REHM SYNERGIC.PRO 251

16 pages

REHM TIG.STAR 170 DC - User Manual

Table of Contents

REHM TIG.STAR 170 DC Specifications

Related product manuals