OWAIRFL
HORIZONTAL LEFT / RIGHT VENT
HORIZONTAL LEFT / RIGHT VENT
HORIZONTAL LEFT / RIGHT VENT
FROM PARTS BAG
(PROVIDED WITH UNIT)
PARTS NEEDED:
FROM CONVERSION KIT RXGY-CK
2-5/8"
PARTS NEEDED:
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
FROM THE
YOU MUST HAVE THE PARTS OUTLINED BELOW FROM THESE KITS
BEFORE PROCEEDING.
!
FROM CONVERSION KIT RXGY-CK
(X4)
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
PARTS BAG, CONVERSION KIT RXGY-CK
YOU MUST HAVE THE PARTS OUTLINED BELOW FROM THESE KITS
BEFORE PROCEEDING.
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
RXGY-CK AND RXGY-ZK.
YOU MUST HAVE THE PARTS OUTLINED BELOW FROM THESE KITS
INTAKE
COUPLING
AND NUT
INTAKE AIR
DIFFUSER
FROM CONVERSION KIT RXGY-ZK
(X10)
INTAKE AIR
DIFFUSER
2-5/8" FLUSH
MOUNT PLUG
FROM CONVERSION KIT RXGY-ZK
(X2)
MOUNT PLUG
1/4" BLACK
VENT TUBE
#8 X 1/2"
SCREW
.559" CONDENSATE
TRAP DRAIN PLUG
1/2" DRAIN
HOSE E
1/2" DRAIN
HOSE E
1/2" VINYL
CAP (YELLOW)
O-RING
#8 X 1/2"
SCREW
TOOLS/MATERIALS NEEDED:
ELECTRIC DRILL 1/8" DRILL BIT 3/16" DRILL BIT PLIERS 1/4" HEX HEAD DRIVER 5/16 HEX HEAD DRIVER
PVC GLUE AND PRIMER HAMMER FLAT HEAD SCREWDRIVER TUBING CUTTER
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE.
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN “AS SHIPPED CONDITION”
PIPE COLLAR / GASKET
ASSEMBLY
TOOLS/MATERIALS NEEDED:
ELECTRIC DRILL 1/8" DRILL BIT 3/16" DRILL BIT PLIERS 1/4" HEX HEAD DRIVER 5/16 HEX HEAD DRIVER
PVC GLUE AND PRIMER HAMMER FLAT HEAD SCREWDRIVER TUBING CUTTER
TRANSITION
TRANSITION
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE.
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN “AS SHIPPED CONDITION”
1/2" DRAIN
HOSE G
TOOLS/MATERIALS NEEDED:
ELECTRIC DRILL 1/8" DRILL BIT 3/16" DRILL BIT PLIERS 1/4" HEX HEAD DRIVER 5/16 HEX HEAD DRIVER
PVC GLUE AND PRIMER HAMMER FLAT HEAD SCREWDRIVER TUBING CUTTER
TRANSITION
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE.
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN “AS SHIPPED CONDITION”
INTAKE
PIPE
ELECTRIC DRILL 1/8" DRILL BIT 3/16" DRILL BIT PLIERS 1/4" HEX HEAD DRIVER 5/16 HEX HEAD DRIVER
PVC GLUE AND PRIMER HAMMER FLAT HEAD SCREWDRIVER TUBING CUTTER
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE.
ASSEMBLY
W/ O-RING
ELECTRIC DRILL 1/8" DRILL BIT 3/16" DRILL BIT PLIERS 1/4" HEX HEAD DRIVER 5/16 HEX HEAD DRIVER
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE.
FLUE PIPE
ASSEMBLY
W/ O-RING
1
1a
TRANSITION
COUPLING
(RETAIN)
TRANSITION
(DISCARD)
ELBOW
(RETAIN)
IDB COUPLING
(RETAIN)
HOSE “D”
2
O
V
E
2c
1b
HOSE “D”
(RETAIN)
VENT HOSE
(DISCARD)
M
O
V
2d
HOSE “D”
(RETAIN)
VENT HOSE
(DISCARD)
DISCARD
2b
1a - REMOVE ELBOW, (2) COUPLINGS, AND FLUE TRANSITION.
NOTE:RETAIN ELBOW AND COUPLINGS FOR LATER USE.
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL
STRAIGHT OUT
1a - REMOVE ELBOW, (2) COUPLINGS, AND FLUE TRANSITION.
NOTE:RETAIN ELBOW AND COUPLINGS FOR LATER USE.
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL
2a - INSTALL 2-5/8" FLUSH MOUNT PLUG.
2b - REMOVE LEFT 2-3/8" FLUSH PLUG IN BLOWER SHELF - DISCARD.
2c - RELOCATE RIGHT 2-3/8" FLUSH MOUNT PLUG FROM
BLOWER SHELF TO TOP PLATE.
2d - RELOCATE Ø.403" DRAIN PLUG IN THE COLLECTOR BOX.
2e - REMOVE RECTANGLE FLUSH MOUNT PLUG-DISCARD
1a - REMOVE ELBOW, (2) COUPLINGS, AND FLUE TRANSITION.
NOTE:RETAIN ELBOW AND COUPLINGS FOR LATER USE.
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL
2a - INSTALL 2-5/8" FLUSH MOUNT PLUG.
2b - REMOVE LEFT 2-3/8" FLUSH PLUG IN BLOWER SHELF - DISCARD.
2c - RELOCATE RIGHT 2-3/8" FLUSH MOUNT PLUG FROM
BLOWER SHELF TO TOP PLATE.
2d - RELOCATE Ø.403" DRAIN PLUG IN THE COLLECTOR BOX.
2e - REMOVE RECTANGLE FLUSH MOUNT PLUG-DISCARD
2b - REMOVE LEFT 2-3/8" FLUSH PLUG IN BLOWER SHELF - DISCARD.
2c - RELOCATE RIGHT 2-3/8" FLUSH MOUNT PLUG FROM
2d - RELOCATE Ø.403" DRAIN PLUG IN THE COLLECTOR BOX.
2e - REMOVE RECTANGLE FLUSH MOUNT PLUG-DISCARD
ST-A1194-34-01
To Next Page
Loading...
