36
Field Conversions
6
INSTALL INTAKE COUPLING IN BLOWER SHELF HOLE AS SHOWN.
INSERT AIR DIFFUSER INTO COUPLING UNTIL TABS ARE SEATED.
INSTALL INTAKE COUPLING IN BLOWER SHELF HOLE AS SHOWN.
INSERT AIR DIFFUSER INTO COUPLING UNTIL TABS ARE SEATED.
INSTALL INTAKE COUPLING IN BLOWER SHELF HOLE AS SHOWN.
INSERT AIR DIFFUSER INTO COUPLING UNTIL TABS ARE SEATED.
DIFFUSER
FULLY SEATED
7
FULLY SEATED
NOTE:
DIFFUSER MAY HAVE A TENDENCEY TO FALL OUT OF THE COUPLING AT
THIS STEP. tHE INSTALLER MAY ELECT TO INSTALL THE DIFFUSER
AFTER ROTATING THE FURNACE TO THE HORIZONTAL POSITION.
DIFFUSER MAY HAVE A TENDENCEY TO FALL OUT OF THE COUPLING AT
THIS STEP. tHE INSTALLER MAY ELECT TO INSTALL THE DIFFUSER
AFTER ROTATING THE FURNACE TO THE HORIZONTAL POSITION.
DIFFUSER MAY HAVE A TENDENCEY TO FALL OUT OF THE COUPLING AT
THIS STEP. tHE INSTALLER MAY ELECT TO INSTALL THE DIFFUSER
AFTER ROTATING THE FURNACE TO THE HORIZONTAL POSITION.
7a
PRE-DRILL (4) 1/8"
HOLES AND ATTACH
W/ (4) SCREWS
TYP. (2) PLACES
O-RING
HOLES AND ATTACH
W/ (4) SCREWS
TYP. (2) PLACES
PVC GLUE JOINTPVC GLUE JOINT
INSTALL W/
(2) SCREWS
7b
10c
7a - INSTALL INTAKE PIPE:INSTALL INTAKE PIPE: SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN. SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN.7a - INSTALL INTAKE PIPE:
7b - INSTALL FLUE PIPE ASSEMBLY:
SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER
SHELF WITH (2) SCREWS AS SHOWN. ENSURE O-RING IS PROPERLY SEATED.
7c - SLIDE PIPE COLLAR ASSEMBLIES OVER THE (2) PIPES AND DRILL (8)
SECURE WITH (8) SCREWS AS SHOWN.
INSTALL INTAKE PIPE:
INSTALL FLUE PIPE ASSEMBLY:
SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER
SHELF WITH (2) SCREWS AS SHOWN. ENSURE O-RING IS PROPERLY SEATED.
7c - SLIDE PIPE COLLAR ASSEMBLIES OVER THE (2) PIPES AND DRILL (8)
SECURE WITH (8) SCREWS AS SHOWN.
SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN.
INSERT FLUE PIPE ASSEMBLY THROUGH RIGHT SIDE KNOCKOUT,
SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER
SHELF WITH (2) SCREWS AS SHOWN. ENSURE O-RING IS PROPERLY SEATED.
7c - SLIDE PIPE COLLAR ASSEMBLIES OVER THE (2) PIPES AND DRILL (8) Ø1/8" HOLES USING THE COLLARS AS A TEMPLATE.
SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN.
INSERT FLUE PIPE ASSEMBLY THROUGH RIGHT SIDE KNOCKOUT, (NOTE: SLIDE FROM UNDER PLATE)
SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER
Ø1/8" HOLES USING THE COLLARS AS A TEMPLATE.
SLIDE INTAKE PIPE THROUGH THE LEFT SIDE KNOCKOUT, CLEAN AND PVC GLUE TO INTAKE COUPLING AS SHOWN.
(NOTE: SLIDE FROM UNDER PLATE).
SLIDE ANGLED END THROUGH OPENING IN BLOWER SHELF AND ALIGN WITH ELBOW COUPLING. SECURE PIPE ASSEMBLY TO BLOWER
Ø1/8" HOLES USING THE COLLARS AS A TEMPLATE.
ST-A1194-34-01
To Next Page
Loading...
