To Next PageTo Next PageWhy do documents and reports not print out on my Ricoh Aficio MP 5002 All in One Printer?
Documents and reports might not print out from your Ricoh All in One Printer if the paper output tray is full. Remove the prints from the tray. Also, check if there is paper left. If the tray is empty, load paper.
What to do if Ricoh All in One Printer is unable to connect to the network?
If your Ricoh All in One Printer is unable to connect to the network, it indicates a network error. Press [Check] in the function where the error occurred, then check the displayed message and take appropriate action. Check that the machine is correctly connected to the network and that the machine is correctly set. If the indicator is still lit after trying to solve the problem, contact your service representative or your administrator.
What does it mean when 'Please wait.' appears on Ricoh Aficio MP 5002?
The message 'Please wait.' on your Ricoh All in One Printer can appear in several situations: when you press the [Energy Saver] key, when the machine is warming up, or when you change the toner cartridge. Wait for a while. If the machine does not get ready in five minutes, contact your service representative. Also, do not turn off the main power switch while the message is showing.
What to do if an error message remains on Ricoh All in One Printer after removing misfed paper?
If an error message remains on your Ricoh All in One Printer even after removing misfed paper: * When a misfeed message appears, it remains until you open and close the cover as required. * Paper is still jammed in the tray. Remove misfed paper, and then open and close the cover.
What to do if I cannot print in duplex mode on my Ricoh Aficio MP 5002?
If you cannot print in duplex mode on your Ricoh All in One Printer: * You may have selected a paper tray that is not set for duplex printing. Change the setting for 'Apply Duplex' in System Settings to enable duplex printing for the paper tray. * You may have selected a paper type that cannot be used for duplex printing. In [Tray Paper Settings], select a paper type that can be used for duplex printing.
What to do if an error has occurred on Ricoh Aficio MP 5002 All in One Printer?
If an error has occurred on your Ricoh All in One Printer, a function with the status 'Error Occurred' in the [Check Status] screen is defective. Press [Check] in the function where the error occurred, then check the displayed message and take appropriate action. You can use other functions normally.
What to do if misfeeds occur frequently in Ricoh All in One Printer?
If misfeeds occur frequently in your Ricoh All in One Printer, it could be due to several reasons: * The tray's side or end fences may not be set properly. Check that the side or end fences are set properly and that the side fences are locked. * Paper of undetectable size has been loaded. If you load a paper size that is not selected automatically, you need to specify the paper size with the control panel. * There is a foreign object on the finisher tray. Do not place anything on the finisher tray.
What to do if my Ricoh All in One Printer is printing on the reverse side of the paper?
If your Ricoh All in One Printer is printing original images on the reverse side of the paper, it may be because the paper is loaded incorrectly. Load paper into the paper tray or tray 3 (LCT) with the print side up. Load paper into the Large capacity tray (LCT), or bypass tray with the print side down.
What to do if 'Following output tray is full. Remove paper.' appears on Ricoh All in One Printer?
When the message 'Following output tray is full. Remove paper.' appears on your Ricoh All in One Printer, it means that the output tray is full. To resume printing, remove paper from the output tray. If paper is going to the finisher shift tray, press the [Stop] key to suspend printing to prevent paper from falling, then remove the paper. Finally, press [Continue] on the display panel to resume printing.
General| Print Speed | 50 ppm |
|---|---|
| Print Resolution | 1200 x 1200 dpi |
| Copy Resolution | 600 x 600 dpi |
| Duplex Printing | Yes |
| Functions | Print, Copy, Scan, Fax |
| Maximum Paper Size | A3 |
| Warm-up Time | 20 seconds |
| Memory (Standard) | 1 GB |
| Hard Disk Drive | 160 GB |
| Power Source | 220 - 240 V, 50/60 Hz |
| Fax Resolution | 200 x 200 dpi |
| Scan Resolution | 600 dpi |
| Connectivity | USB, Ethernet |
| Memory (Maximum) | 1.5 GB RAM |
| PDL (Page Description Language) | PCL6, PostScript 3, PDF |
| Copy Speed | 50 cpm |
| Network Connectivity | Ethernet 10/100Base-TX |
| Operating System Compatibility | Windows, Mac |
Protect documents from unauthorized access and prevent copying without permission.
Identifies and explains the functions of the machine's various parts.
Details the names and functions of the buttons and displays on the control panel.
Step-by-step guide on how to make copies using the machine.
Outlines the fundamental steps for sending faxes using memory transmission.
Explains how to perform basic printing tasks using the machine.
