Ricoh Toscana-P1 - User Manual

Questions and Answers

J
jamesemilyAug 19, 2025
What to do if my Ricoh All in One Printer says 'SC978 Left ink collection tank'?
- J
  Janet HancockSep 12, 2025
  If your Ricoh All in One Printer displays the error 'SC978 Left ink collection tank', it means the ink collection tank sensor has detected a full condition. You can try cycling the printer off and on to see if that resolves the issue. If not, print the System Summary by pushing [Menu], selecting "List/Test Print" then push [#Enter] and check the Total Counter reading. If necessary, replace the left ink collection tank.
J
Jamie BrockAug 21, 2025
What to do if I see 'SC993 High voltage leak' on my Ricoh All in One Printer?
- B
  Brian Olson DVMAug 21, 2025
  If your Ricoh All in One Printer shows the error 'SC993 High voltage leak', it means the leak detection signal went ON and didn't change, possibly due to ink or condensation on the transport belt. First, try cycling the printer off and on. Then, raise the top cover and inspect the transfer belt surface. You can also run the De-Condensation function by pushing [Menu], selecting "Maintenance"> "De-Condensation" to feed 3 sheets of blank paper through the paper path. Clean any ink from the transport belt. If the issue persists, the HVPS pack may need replacement.
P
Peggy GonzalezAug 23, 2025
How to fix 'SC994 Vertical motor error' on Ricoh All in One Printer?
- M
  matthewhendersonAug 23, 2025
  If your Ricoh All in One Printer displays the error 'SC994 Vertical motor error', it indicates that the vertical motor is not rotating, the encoder sensor signal did not change, or there is a paper jam. Try cycling the printer off and on. Also, remove any paper jams. If the problem continues, the encoder sensor or the vertical motor may need to be replaced.
T
Taylor MoonAug 26, 2025
What causes 'SC996 No input from the horizontal encoder sensor' error on Ricoh All in One Printer?
- B
  brownheatherAug 26, 2025
  If your Ricoh All in One Printer shows the error 'SC996 No input from the horizontal encoder sensor', it could be due to several reasons: no input from the horizontal encoder sensor, the encoder sensor signal did not change, the encoder strip is dirty or scratched, or the horizontal motor is not rotating. First, try cycling the printer off and on. Confirm that the film encoder is not loose. If the issue persists, the horizontal motor may need to be replaced.
S
sandra72Aug 27, 2025
How do I troubleshoot 'SC997 Horizontal encoder abnormal' on my Ricoh All in One Printer?
- M
  mitchellmelissaAug 28, 2025
  If your Ricoh All in One Printer displays the error 'SC997 Horizontal encoder abnormal', it means the encoder sensor signal did not change, or the encoder strip is dirty or scratched. To resolve this, start by cycling the printer off and on. If the problem persists, you may need to replace the encoder sensor. Also, check the encoder film position and the carriage FFC (Flat Film Connector).
A
Ashley GreenAug 29, 2025
Why is my Ricoh All in One Printer showing 'SC990 Ink level sensor feeler out of position'?
- N
  Nicole WellsAug 30, 2025
  If your Ricoh All in One Printer displays the error 'SC990 Ink level sensor feeler out of position', it could be due to the cap of the maintenance unit not rising toward the carriage. Try cycling the printer off and on. Clean the suction cap. If that doesn't work, consider replacing the horizontal encoder film strip or the maintenance unit. Also, check the position of the feelers attached to the sides of the tanks.
S
Sonya ThomasSep 1, 2025
What does 'SC984 DRV circuit temperature abnormal' mean on my Ricoh All in One Printer?
- F
  fwatkinsSep 1, 2025
  If your Ricoh All in One Printer displays the error 'SC984 DRV circuit temperature abnormal', it indicates that the signal from the temperature sensor on the control board did not change. Try cycling the printer off and on to see if it resolves the issue. Also, check the fan operation. If the problem persists, the control board may need to be replaced.
A
Austin PorterSep 3, 2025
What to do if Ricoh All in One Printer displays 'SC973 EEPROM write error'?
- A
  Aaron MendezSep 3, 2025
  If your Ricoh All in One Printer displays the error 'SC973 EEPROM write error', it indicates that the NVRAM EEPROM is defective. First, try cycling the printer off and on. If the issue persists, you may need to replace the EEPROM (NVRAM) or the control board.
I
isabellamillerSep 5, 2025
How to fix 'SC972 Flash ROM verify error' on Ricoh All in One Printer?
- A
  anthonydavisSep 5, 2025
  If your Ricoh All in One Printer displays the error 'SC972 Flash ROM verify error', it indicates a defective Flash ROM. Try cycling the printer off and on, and if the error persists, you may need to replace the control board.
K
Kristen EllisSep 7, 2025
What causes 'SC971 Flash ROM write error' on Ricoh All in One Printer?
- B
  Brian ElliottSep 7, 2025
  If your Ricoh All in One Printer displays the error 'SC971 Flash ROM write error', it indicates a defective Flash ROM. Try cycling the printer off and on. If the error persists, you may need to replace the control board.