To Next PageTo Next Page
Need help?Do you have a question about the RIDGID R41221 and is the answer not in the manual?
General| Type | Table Saw |
|---|---|
| Motor Power | 15 amps |
| Arbor Size | 5/8 inches |
| Voltage | 120 V |
| Maximum Speed | 5000 RPM |
| Blade Diameter | 10 inches |
| Max Rip Capacity | 30 inches |
| Bevel Capacity | 0 - 45° |
| Cord Length | 6 ft |
| No Load Speed | 5, 000 RPM |
Guidelines for user's safety and attentiveness during operation.
Instructions for maintaining a safe and clean work environment.
Precautions regarding electrical connections and usage of the tool.
Best practices for operating and maintaining the power tool safely.
Ensuring workpiece is properly secured and table is clear for safe cutting.
Warnings against unsafe hand positioning relative to the blade and avoiding cross-handing.
Importance of stable mounting, planning, and avoiding freehand cuts.
Guidelines for selecting, inspecting, and using extension cords and tool cords.
Information on polarized plugs and general electrical safety precautions.
Emphasizes reading the manual and wearing proper personal protective equipment.
Rules for safe tool operation including stance, guards, setup, and handling.
Warnings about laser exposure and securing the saw to prevent tipping.
Explanation of danger, warning, caution, and notice signal words.
Definitions and explanations for various symbols used on the tool.
Explanation of double insulation and its safety benefits.
Requirements for connecting the tool to a power supply.
Guidance on selecting and using extension cords with the tool.
Detailed technical specifications for the miter saw.
Labels and descriptions of the saw's main parts and features.
Introduction to the saw's functions and safety awareness.
Details on adjusting bevel stops for precise angle settings.
Information on the carrying handle and detent override lever functionality.
Explanation of the electric brake and laser guide features.
How to use the miter lock lever and understanding positive stops.
Information on the self-retracting blade guard and spindle lock.
Details on sliding fences, securing the switch trigger, and padlock use.
Functionality of the zero bevel stop button for precise 0° cuts.
Steps for safely unpacking and inspecting the saw.
Warnings and procedures for handling the spring-loaded saw arm.
Guidance on checking for shipping damage and ensuring proper support.
Critical safety warning about securing the saw to prevent tipping.
Instructions for securely mounting the miter saw to a workbench or stand.
Steps for attaching the sliding miter fences to the saw.
How to use the blade wrench and install the dust bag.
How to install and use the work clamp for securing workpieces.
Detailed instructions for safely installing or replacing the saw blade.
Proper alignment of blade washers and secure tightening of the blade bolt.
Correct blade installation direction and ensuring lower blade guard function.
Procedure for cutting slots in the throat plate for blade clearance.
How to align and use the laser guide for accurate cuts.
Procedures for locking and unlocking the saw arm for transport and operation.
Steps to ensure the saw blade is perpendicular to the fence at 0 degrees.
How to use a square to check blade alignment with the fence.
Adjusting the fence to achieve parallel alignment with the saw blade.
How to reset scale indicators after squaring adjustments.
Aligning the saw blade perpendicular to the miter table at 0 degrees.
Aligning the saw blade perpendicular to the miter table at 45 degrees.
Critical safety reminders for operating the miter saw.
Designed uses for the miter saw, including wood and plastic cutting.
Importance of securing the saw and keeping hands clear of the blade.
Verifying no interference and securing angles before cutting.
Step-by-step guide for performing miter and cross cuts.
How to position and align workpieces for accurate cuts.
Steps for performing a dry run and ensuring blade reaches full speed.
Instructions for making straight bevel cuts with the saw.
How to set and secure the desired bevel angle for cuts.
Guide to making cuts with both miter and bevel angles simultaneously.
Understanding how miter and bevel settings affect each other.
Importance of test cuts and proper workpiece positioning.
Methods for supporting long workpieces during cutting.
Techniques for clamping wide workpieces securely.
Instructions for creating and attaching an auxiliary fence.
A chart providing miter and bevel settings for popular structures.
Techniques for accurately cutting crown molding with the saw.
Method for positioning crown molding flat on the miter table for cuts.
Procedure for nesting crown molding against the fence using block stops.
Guidelines for safely cutting warped or bowed material.
Critical warning to unplug the tool before making any adjustments.
Note that factory pivot adjustments typically do not require readjustment.
Steps for ensuring smooth bevel pivot and adjusting to 45 degrees.
How to adjust the saw arm to a precise 0° bevel angle.
Detailed steps for aligning the laser guide for accurate cutting.
Safety warning regarding laser radiation exposure during adjustments.
How to adjust the miter lock lever for proper table tension and security.
Warnings and advice for safe maintenance practices.
Guidance on cleaning plastic parts and information on lubrication.
Step-by-step guide for replacing worn carbon brushes.
Details of the limited warranty coverage for the power tool.
Information on the 90-day return policy for customer satisfaction.
Procedures for contacting service centers and requesting warranty repairs.
What is not covered by the warranty and legal limitations.
